Bedienungsanleitung Makita EW2051H (Seite 14 von 32) (Alle Sprachen)

690620

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

8. EASY TROUBLESHOOTING

1. PUMP DOES NOT RUN.

■

Engine dose not start.

(See “8.-6. WHEN ENGINE DOES NOT START”)

■

Sticking of impeller (Disassemble and clean.)

2. PUMPING VOLUME IS SMALL.

■

Sucking air at suction side.

(Check piping at suction side.)

■

Drop off engine output.

(Consult your nearest dealer.)

■

Breakage of mechanical seal.

(Consult your nearest dealer.)

■

High suction lift (Lower.)

■

Suction hose is too long or thin.

(Use a thick hose in minimum length.)

■

Leak of water from water passage. (Stop leaking.)

■

Clogging of foreign substance in impeller.

(Disassemble and clean.)

■

Wear of impeller.

■

Strainer is clogged. (Clean.)

■

Engine speed is too low.

(Consult your nearest dealer.)

3. PUMP DOES NOT SELFPRIME.

■

Suction of air at suction side.

(Check piping at suction side.)

■

Insufcient priming water inside pump casing.

(Prime fully.)

■

Imperfect tightening of drain plug.

(Tighten the plugs completely.)

■

Engine speed is too low.

(Consult your nearest dealer.)

■

Sucking air from mechanical seal.

(Consult your nearest dealer.)

4. DELIVERY HOSE DOES NOT STAY ON

COUPLING.

■

Hose may be kinked or discharge end may be

blocked or clogged. (Straighten or clean.)

5. PUMP SUDDENLY STOPS.

■

Solid object preventing pump-rod from completing

stroke. (Disassemble and clean.)

6. WHEN ENGINE DOES NOT START:

Perform the following checks before you take the pump

to your Makita dealer. If you still have trouble after

completing the checks, take the pump to your nearest

Makita dealer.

(1) Is there a strong spark across the electrode?

■

Is the stop switch at position “ I ” (ON)?

■

Remove and inspect the spark plug.

If the electrode is fouled, clean or replace it with

new one.

■

Remove the spark plug and connect it to the plug

cap. Pull the starter handle while grounding spark

plug against engine body. Try with a new spark plug

if the spark is weak or there is no spark.

The ignition system is faulty if there is no spark with

a new spark plug.

WARNING

■

Wipe out spilled fuel carefully before

testing. Place spark plug as far away from

spark plug hole as possible.

■

Do not hold spark plug by hand while

pulling recoil starter.

NOTE

The engine with oil sensor will stop automatically

when the oil level falls below the prescribed limit.

Unless the oil level is raised above the prescribed

limit, the engine will stop immediately after starting.

(2) Is there enough compression?

Pull the starter handle slowly and check if

resistance is felt.

If little force is required to pull the starter handle,

check if the spark plug is tightened rmly. If the

spark plug is loose, tighten it.

(3) Is the spark plug wet with gasoline?

■

Is the fuel valve opened?

■

Choke (close choke lever) and pull the starter

handle ve or six times. Remove the plug and

check if its electrode is wet. If the electrode is wet,

fuel is well supplied to your engine.

■

When the electrode is dry, check where the fuel

stops. (Check the fuel intake of the carburetor.)

■

In case the engine does not start with well supplied

fuel, try using fresh fuel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EW2051H Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info