Bedienungsanleitung Makita EY2650H (Seite 6 von 264) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

599913

Zoom out

Zoom in

Vorherige Seite

1/264

Nächste Seite

- Pay attention to the environment. Avoid unnecessary throttle operation for

less pollution and noise emissions. Adjust the carburetor correctly.

- During or after operation, do not put the hot equipment onto dry grass or

combustible materials.

- Do not hold your right hand above shoulder height.

- During operation, never hit the saw chain against hard obstacles such stones

and nails. Take particular care when cutting branches next to walls, wire

fences or the like.

- If branches get caught in the saw chain, always stop the engine and remove

the spark plug cap. Otherwise unintentional start may cause serious injury.

- If the saw chain becomes clogged, always stop the engine and remove the

spark plug cap before cleaning.

- Accelerating the engine with the saw chain blocked increases the load and

will damage the engine and/or clutch.

- Before cutting limbs, keep an escape area away from the falling limb. First,

clear obstructs such as limbs and branches from the work area. Move all

tools and goods from the escape area to another safe place.

- Before cutting branches and limbs, check the falling direction of them,

considering the condition of branches and limbs, adjoining trees, wind

direction, etc. Pay full attention to the falling direction, and the rebound of the

branch, which hit the ground.

- Never hold the pole saw at an angle of more than 60°. Otherwise falling

objects can hit the operator and cause serious injury. Never stand underneath

the limb being cut.

- Pay attention to broken or bent branches. They may bounce back in cutting,

causing unexpected injury.

- Before cutting limbs that you intend to cut, remove branches and leaves

around them. Otherwise the saw may be caught by them.

- To prevent the saw from being caught in the kerf, do not release the throttle

lever before pulling the saw out of the kerf.

- If the saw chain is bound in the kerf, immediately stop the engine, carefully

move the branch to open the kerf and release the saw.

- Avoid kickback (rotational reactive force towards the operator). To prevent

kickback, never use the guide bar nose or perform a penetrating cut. Always

beware of the position of the guide bar nose.

- Check the chain tension frequently. When checking or adjusting the chain

tension, stop the engine and remove the spark plug cap. If the tension is

loose, tighten it.

- Operate the equipment with as little noise and contamination as possible. In

particular check the correct setting of the carburetor.

- Never stand on a ladder and run the equipment.

- Never climb up into trees to perform cutting operation.

- Wait until the chain reaches its full working speed before cutting.

- Take a rest to prevent loss of control caused by fatigue. We recommend to

take a 10 to 20-minute rest every hour.

Transport

- Before transporting the equipment, switch off the engine and remove the

spark plug cap.

- $OZD\V¿WWKHJXLGHEDUFRYHUGXULQJWUDQVSRUWDWLRQ

- Always use the tool protection included with the equipment.

- &DUU\LWLQDKRUL]RQWDOSRVLWLRQE\KROGLQJWKHVKDIW.HHSWKHKRWPXIÀHU

away from your body.

- When transporting the equipment in a vehicle, properly secure it to avoid

turnover. Otherwise fuel spillage and damage to the equipment and other

baggage may result.

- Shut off the engine during transport.

- Ensure that the fuel tank is completely empty.

- When unloading the equipment from the truck, never drop the engine to the

ground or this may severely damage the fuel tank.

- Remember to lift the entire equipment from the ground when moving the

equipment. Dragging the fuel tank is highly dangerous and will cause damage

DQGOHDNDJHRIIXHOSRVVLEO\FDXVLQJ¿UH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EY2650H Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info