Bedienungsanleitung Makita G 1700i (Seite 13 von 24) (Englisch)

448423

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISHFRANÇAISEESPAÑOL

(d) Turn on the switch of the appliance.

NOTE

If the generator is stopped with the overload pilot

lamp turned on, the generator will be in the

overload condition and/or the electrical

appliance(s) would be out of order.

In this case, stop the engine immediately and

check the appliance and/or generator for overloading.

After the check and remedy, restarting the engine

will resume displaying in the normal manner.

(2) DC APPLICATION (See Fig.

)

The DC terminal is used only for charging 12 volt

batteries. It provides up to 12V-8.3A (100W) of

maximum power.

q Positive terminal (RED)

w Negative terminal (BLACK)

CONNECTION OF CABLE :

Connect positive terminal (red) on generator

to positive (+) terminal on battery.

Connect negative terminal (black) on

generator to negative (

) terminal on battery.

SAFETY PRECAUTIONS WHILE CHARGING

An explosive hydrogen gas is discharged

through vent holes in the battery during the

charging process. Do not allow spark or open

flame around the generator or battery during the

charging process.

Electrolyte fluid can burn eyes and clothing.

Be extremely careful to avoid contact. If injured,

wash the affected area immediately with large

quantities of water and consult a doctor for

treatment.

When charging a large capacity battery or

totally discharged battery, excessive current

may force the DC breaker to turn off.

In such cases, use a battery charger to charge

a large battery with AC output.

Battery defects may cause the DC breaker to turn off.

Check the battery before replacing the DC breaker.

3. STOPPING THE GENERATOR

(a) Turn off the power switch of the electric

equipment and unplug the cord from receptacle

of the generator.

(b) Allow the engine about 3 minutes to cool down

at no load before stopping.

(c)

Turn the engine switch to the position

(STOP). (See Fig. 4-y)

4. OIL SENSOR (See Fig.

)

(a) The oil sensor detects the fall in oil level in the

crankcase and automatically stops the engine

when the oil level falls below a predetermined level.

(b)

When engine has stopped automatically, switch off

generator's no fuse breaker, and check the oil level.

Refill engine oil to the upper level as instructed

on page 6 and restart the engine.

(c)

If the engine dose not start by usual starting

procedures, check the oil level

q OIL SENSOR

Do not remove OIL SENSOR PROBE when

refilling with oil.

Remove oil filler cap on the opposite side

of carburetor.

CAUTION

Do not use the DC terminal at a time

while using the AC out put.

CAUTION

Be sure to ground the generator if the

connected electrical device is grounded.

Failure to ground unit could lead to

electrical spark.

WARNING

Do not put foreign objects into the plug

receptacle.

CAUTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita G 1700i Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita G 1700i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info