Bedienungsanleitung Makita G 1700i (Seite 14 von 24) (Englisch)

448423

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISHFRANÇAISEESPAÑOL

Electrical loads such as incandescent lamps and hot plates require the same wattage to start as is

needed to maintain use.

Loads such as fluorescent lamps require 1.2

to 2 times the indicated wattage during start-up.

Loads for mercury lamps require 2 to 3 times the indicated wattage during start-up.

Electrical motors require a large starting current. Power requirements depend on the type of motor and

its use. Once enough "surge" is attained to start the motor, the appliance will require only 50% to 30%

of the wattage to continue running.

Most electrical tools require 1.2 to 3 times their wattage for running under load during use. For example,

a 5000 watt generator can power a 1800 to 4000 watt electrical tool.

Loads such as submersible pumps and air compressors require a very large force to start. They need 3

to 5 times the normal running wattage in order to start.

For example, a 5000 watt generator would only be able to drive a 1000 to 1700 watt pump.

Some appliances need a "surge" of energy when starting.

This means that the amount of electrical power

needed to start the appliance may exceed the amount needed to

maintain its use.

Electrical appliances and tools normally come with a label indicating voltage, cycles / Hz, amperage (amps)

and electrical power needed to run the appliance or tool.

Check with your nearest dealer or service center with questions regarding power surge of certain appliances

or power tools.

6. WATTAGE INFORMATION

To determine the total wattage required to run a

particular electrical appliance or tool, multiply the

voltage figure of the appliance/tool by the amperage

(amps) figure of same. The voltage and amperage

(amps) information can be found on a name plate

which is normally attached to electrical appliances

and tools.

NOTE

The following wattage chart is general guide only. Refer to your specific appliance for

correct wattage.

Applicable Wattage (W)

60 Hz

approx. 1350

approx. 700

approx. 400

approx. 300

Applications

Incandescent lamp, Heater

Fluorescent lamp, Electric tool

Mercury lamp

Pump, Compressor

VOLTAGE DROP IN ELECTRIC EXTENSION CORDS

When a long electric extension cord is used to connect an appliance or tool to the generator, a certain amount of

voltage drop or loss occurs in the extension cord which reduces the effective voltage available for the appliance or tool.

The chart below has been prepared to illustrate the approximate voltage loss when an extension

cord of 300 feet

(approx. 100 meters) is used to connect an appliance or tool to the generator.

Nominal

cross

section

A.W.G.

Allowable

current

No.of strands

/ strands dia.

Resistance

Current Amp.

No./mm

/100m

No. A 1A 3A 5A 8A 10A 12A 15A

0.75 18 7 30/0.18 2.477 2.5V 8V

12.5V

Voltage drop

1.27 16 12 50/0.16 1.486 1.5V 5V 7.5V 12V 15V 18V

2.0 14 17 37/0.26 0.952 1V 3V 5V 8V 10V 12V 15V

3.5 12 to 10 23 45/0.32 0.517 1.5V 2.5V 4V 5V 6.5V 7.5V

5.5 10 to 8 35 70/0.32 0.332 1V 2V 2.5V 3.5V 4V 5V

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita G 1700i Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita G 1700i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info