Bedienungsanleitung Makita GA4041C (Seite 11 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599684

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

• During cutting operations, never change the angle of

the wheel. Placing side pressure on the cut-off wheel

(as in grinding) will cause the wheel to crack and break,

causing serious personal injury.

• A diamond wheel shall be operated perpendicular to

the material being cut.

Operation with wire cup brush (optional

accessory) (Fig. 20)

CAUTION:

• Check operation of brush by running tool with no load,

insuring that no one is in front of or in line with brush.

• Do not use brush that is damaged, or which is out of

balance. Use of damaged brush could increase poten-

tial for injury from contact with broken brush wires.

Unplug tool and place it upside down allowing easy

access to spindle. Remove any accessories on spindle.

Thread wire cup brush onto spindle and tighten with sup-

plied wrench. When using brush, avoid applying too

much pressure which causes over bending of wires,

leading to premature breakage.

Operation with wire wheel brush (optional

accessory) (Fig. 21)

CAUTION:

• Check operation of wire wheel brush by running tool

with no load, insuring that no one is in front of or in line

with the wire wheel brush.

• Do not use wire wheel brush that is damaged, or which

is out of balance. Use of damaged wire wheel brush

could increase potential for injury from contact with bro-

ken wires.

• ALWAYS use guard with wire wheel brushes, assuring

diameter of wheel fits inside guard. Wheel can shatter

during use and guard helps to reduce chances of per-

sonal injury.

Unplug tool and place it upside down allowing easy

access to spindle. Remove any accessories on spindle.

Thread wire wheel brush onto spindle and tighten with

the wrenches.

When using wire wheel brush, avoid applying too much

pressure which causes over bending of wires, leading to

premature breakage.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean. Regularly

clean the tool’s air vents or whenever the vents start to

become obstructed. (Fig. 22)

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Dust cover attachment

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GA4041C Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info