Bedienungsanleitung Makita GA6040 (Seite 8 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599766

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Shaft lock (Fig. 1)

CAUTION:

• Never actuate the shaft lock when the spindle is mov-

ing. The tool may be damaged.

Press the shaft lock to prevent spindle rotation when

installing or removing accessories.

Switch action (Fig. 2)

CAUTION:

• Before plugging in the tool, always check to see that

the slide switch actuates properly and returns to the

“OFF” position when the rear of the slide switch is

depressed.

• Switch can be locked in “ON” position for ease of oper-

ator comfort during extended use. Apply caution when

locking tool in “ON” position and maintain firm grasp on

tool.

To start the tool, slide the slide switch toward the “I (ON)”

position by pushing the rear of the slide switch. For con-

tinuous operation, press the front of the slide switch to

lock it.

To stop the tool, press the rear of the slide switch, then

slide it toward the “O (OFF)” position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing side grip (handle) (Fig. 3)

CAUTION:

• Always be sure that the side grip is installed securely

before operation.

Screw the side grip securely on the position of the tool as

shown in the figure.

Installing or removing wheel guard (For

depressed center wheel, flap disc, flex wheel,

wire wheel brush / abrasive cut-off wheel,

diamond wheel) (Fig. 4, 5 & 6)

WARNING:

• When using a depressed center wheel, flap disc, flex

wheel or wire wheel brush, the wheel guard must be fit-

ted on the tool so that the closed side of the guard

always points toward the operator.

• When using an abrasive cut-off / diamond wheel, be

sure to use only the special wheel guard designed for

use with cut-off wheels. (In some European countries,

when using a diamond wheel, the ordinary guard can

be used. Follow the regulations in your country.)

For tool with locking screw type wheel guard

Mount the wheel guard with the protrusions on the wheel

guard band aligned with the notches on the bearing box.

Then rotate the wheel guard around 180° counterclock-

wise. Be sure to tighten the screw securely.

To remove wheel guard, follow the installation procedure

in reverse.

For tool with clamp lever type wheel guard

Pull the lever in the direction of the arrow after loosening

the screw. Mount the wheel guard with the protrusions on

the wheel guard band aligned with the notches on the

bearing box. Then rotate the wheel guard around 180°.

Tighten the wheel guard with fastening the screw after

pulling lever in the direction of the arrow. The setting

angle of the wheel guard can be adjusted with the lever.

To remove wheel guard, follow the installation procedure

in reverse.

Installing or removing depressed center wheel or

flap disc (optional accessory) (Fig. 7 & 8)

WARNING:

• When using a depressed center wheel or flap disc, the

wheel guard must be fitted on the tool so that the

closed side of the guard always points toward the oper-

ator.

Mount the inner flange onto the spindle. Fit the wheel/

disc on the inner flange and screw the lock nut onto the

spindle.

To tighten the lock nut, press the shaft lock firmly so that

the spindle cannot revolve, then use the lock nut wrench

and securely tighten clockwise.

To remove the wheel, follow the installation procedure in

reverse.

Super flange (optional accessory)

Models with the letter F are standard-equipped with

Super flange. Only 1/3 of efforts needed to undo lock nut,

compared with conventional type.

Installing or removing Ezynut (optional

accessory) (Fig. 9, 10, 11 & 12)

CAUTION:

• Do not use Ezynut with Super Flange or angle grinder

with “F” on the end of the model No. Those flanges are

so thick that the entire thread cannot be retained by the

spindle.

Mount inner flange, abrasive wheel and Ezynut onto the

spindle so that Makita Logo on Ezynut faces outside.

Press shaft lock firmly and tighten Ezynut by turning the

abrasive wheel clockwise as far as it turns.

Turn the outside ring of Ezynut counterclockwise to

loosen.

NOTE:

• Ezynut can be loosened by hand as long as the arrow

points the notch. Otherwise a lock nut wrench is

required to loosen it. Insert one pin of the wrench into a

hole and turn Ezynut counterclockwise.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GA6040 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info