Bedienungsanleitung Makita GA7010C (Seite 5 von 10) (Englisch, Holländisch)

448435

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

ENGLISH

Explanation of general view

1 Shaft lock

2 Switch trigger

3 Lock lever

4 Side grip

5 Wheel guard

6 Bearing box

7Screw

8Lever

9 Lock nut

10 Depressed center wheel/Multi

disc

11 Inner flange

12 Lock nut wrench

13 Exhaust vent

14 Inhalation vent

15 Commutator

16 Insulating tip

17 Carbon brush

18 Screwdriver

19 Brush holder cap

SPECIFICATIONS

Model GA7010C/GA7010CF GA9010C/GA9010CF

Depressed center wheel diameter ...............................................180 mm 230 mm

Spindle thread .............................................................................M14 M14

No load speed (min

-1

) ..................................................................8,400 6,000

Overall length ..............................................................................453 mm 453 mm

Net weight ....................................................................................3.4 kg 3.4 kg

Safety class .................................................................................. /II /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for grinding, sanding and cutting of

metal and stone materials without the use of water.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

ENB031-6

1. Always use eye and ear protection. Other per-

sonal protective equipment such as dust mask,

gloves, helmet and apron should be worn.

2. Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

3. Keep guards in place.

4. Use only wheels with correct size and wheels

having a maximum operating speed at least as

high as the highest No Load Speed marked on

the tool’s nameplate. When using depressed

center wheels, be sure to use only fiberglass-

reinforced wheels.

5. Check the wheel carefully for cracks or damage

before operation. Replace cracked or damaged

wheel immediately.

6. Observe the instructions of the manufacturer for

correct mounting and use of wheels. Handle and

store wheels with care.

7. Do not use separate reducing bushings or adap-

tors to adapt large hole abrasive wheels.

8. Use only flanges specified for this tool.

9. Do not damage the spindle, the flange (espe-

cially the installing surface) or the lock nut. Dam-

age to these parts could result in wheel

breakage.

10. For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length.

11. Before using the tool on an actual workpiece,

test run the tool at the highest no load speed for

at least 30 seconds in a safe position. Stop

immediately if there is any vibration or wobbling

that could indicate poor installation or a poorly

balanced wheel. Check the tool to determine the

cause.

12. Check that the workpiece is properly supported.

13. Hold the tool firmly.

14. Keep hands away from rotating parts.

15. Make sure the wheel is not contacting the work-

piece before the switch is turned on.

16. Use the specified surface of the wheel to per-

form the grinding.

17. Do not use cutting off wheel for side grinding.

18. Watch out for flying sparks. Hold the tool so that

sparks fly away from you and other persons or

flammable materials.

19. Pay attention that the wheel continues to rotate

after the tool is switched off.

20. Do not touch the workpiece immediately after

operation; it may be extremely hot and could

burn your skin.

21. Position the tool so that the power cord always

stays behind the tool during operation.

22. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-

circuit breaker (30 mA) to assure operator safety.

23. Do not use the tool on any materials containing

asbestos.

24. Do not use water or grinding lubricant.

25. Ensure that ventilation openings are kept clear

when working in dusty conditions. If it should

become necessary to clear dust, first disconnect

the tool from the main supply (use non metallic

objects) and avoid damaging internal parts.

26. When use cut-off wheel, always work with the

dust collecting wheel guard required by domes-

tic regulation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GA7010C Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita GA7010C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info