Bedienungsanleitung Makita GA9063 (Seite 6 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691768

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

6 ENGLISH

Work mode: disc sanding with normal side grip

Vibration emission (a

h, DS

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

Work mode: disc sanding with anti vibration side grip

Vibration emission (a

h, DS

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

Model GA9063R

Work mode: surface grinding with normal side grip

Vibration emission (a

h, AG

) : 6.5 m/s

Uncertainty (K) : 1.5 m/s

Work mode: surface grinding with anti vibration side grip

Vibration emission (a

h, AG

) : 5.5 m/s

Uncertainty (K) : 1.5 m/s

Work mode: disc sanding with normal side grip

Vibration emission (a

h, DS

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

Work mode: disc sanding with anti vibration side grip

Vibration emission (a

h, DS

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

NOTE:

The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

NOTE:

The declared vibration emission value may

also be used in a preliminary assessment of exposure.

WARNING:

The vibration emission during actual

use of the power tool can differ from the declared emission

value depending on the ways in which the tool is used.

WARNING: Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it is

running idle in addition to the trigger time).

WARNING: The declared vibration emission

value is used for main applications of the power tool.

However if the power tool is used for other applica-

tions, the vibration emission value may be different.

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Grinder safety warnings

Safety Warnings Common for Grinding, Sanding,

Wire Brushing, or Abrasive Cutting-Off Operations:

This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and specications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, re and/or serious injury.

Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not designed

may create a hazard and cause personal injury.

Do not use accessories which are not specically

designed and recommended by the tool manufac

turer. Just because the accessory can be attached to

your power tool, it does not assure safe operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and y apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

anges, the arbour hole of the accessory must t the

locating diameter of the ange. Accessories that do not

match the mounting hardware of the power tool will run out of

balance, vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of the

rotating accessory and run the power tool at maxi-

mum no-load speed for one minute. Damaged acces-

sories will normally break apart during this test time.

Wear personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As appropri-

ate, wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping small

abrasive or workpiece fragments. The eye pro

tection must be capable of stopping ying debris

generated by various operations. The dust mask

or respirator must be capable of ltrating particles

generated by your operation. Prolonged exposure

to high intensity noise may cause hearing loss.

Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may y away and

cause injury beyond immediate area of operation.

10.

Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a "live" wire

may make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

Makita GA9063 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info