Bedienungsanleitung Makita GD0800C (Seite 5 von 44) (Deutsch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448456

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the slide switch actuates properly and returns to the

“OFF” position when the rear of the slide switch is

depressed.

To start the tool, slide the slide switch toward the “I (ON)”

position. For continuous operation, press the front of the

slide switch to lock it.

To stop the tool, press the rear of the slide switch, then

slide it toward the “O (OFF)” position.

Speed adjusting dial (Fig. 2)

The tool speed can be changed by turning the speed

adjusting dial to a given number setting from 1 to 5.

Higher speed is obtained when the dial is turned in the

direction of number 5. And lower speed is obtained when

it is turned in the direction of number 1.

Refer to the table for the relationship between the num-

ber settings on the dial and the approximate tool speed.

006478

CAUTION:

• If the tool is operated continuously at low speeds for a

long time, the motor will get overloaded, resulting in

tool malfunction.

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing the side handle (Fig. 3)

Always use the side handle to ensure operating safety.

Install the side handle on the tool barrel, then tighten the

handle by turning clockwise at the desired position.

Installing or removing wheel point (Fig. 4 & 5)

Loosen the collet nut and insert the wheel point into the

collet nut. Use the smaller wrench to hold the spindle and

the larger one to tighten the collet nut securely.

The wheel point should not be mounted more than 8 mm

from the collet nut. Exceeding this distance could cause

vibration or a broken shaft.

To remove the wheel point, follow the installation proce-

dure in reverse.

CAUTION:

• Use the correct size collet cone for the wheel point

which you intend to use.

OPERATION (Fig. 6)

Turn the tool on without the wheel point making any con-

tact with the workpiece and wait until the wheel point

attains full speed. Then apply the wheel point to the

workpiece gently. To obtain a good finish, move the tool

in the leftward direction slowly.

CAUTION:

• Apply light pressure on the tool. Excessive pressure on

the tool will only cause a poor finish and overloading of

the motor.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Wheel points

• Collet cone set (3 mm, 6 mm, 1/4", 1/8")

• Vise holder

• Wrench 13

• Wrench 19

• Side handle set

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

GD0800C GD0810C

Number min

–1

(RPM) min

–1

(RPM)

1 – 2 7,000 – 10,000 1,800 – 2,400

2 – 3 10,000 – 17,000 2,400 – 4,100

3 – 4 17,000 – 24,000 4,100 – 5,800

4 – 5 24,000 – 28,000 5,800 – 7,000

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GD0800C Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita GD0800C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info