Bedienungsanleitung Makita GD0811C (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599697

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

27. Do not touch the workpiece immediately after

operation; it may be extremely hot and could

burn your skin.

28. Observe the instructions of the manufacturer for

correct mounting and use of wheels. Handle and

store wheels with care.

29. Check that the workpiece is properly supported.

30. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-

circuit breaker (30 mA) to assure operator safety.

31. Do not use the tool on any materials containing

asbestos.

32. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high

locations.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1 & 2)

CAUTION:

• Before plugging in the tool, always check to see that

the switch lever actuates properly and returns to the

“OFF” position when released.

• Do not pull the switch lever forcibly without pulling in

the lock-off lever. This may cause switch breakage.

To prevent the switch lever from accidentally pulled, a

lock-off lever is provided.

To start the tool, pull the lock-off lever toward the

operator and then pull the switch lever. Release the

switch lever to stop.

Speed adjusting dial (Fig. 3)

The tool speed can be changed by turning the speed

adjusting dial to a given number setting from 1 to 5.

Higher speed is obtained when the dial is turned in the

direction of number 5. And lower speed is obtained when

it is turned in the direction of number 1.

Refer to the table for the relationship between the

number settings on the dial and the approximate tool

speed.

014992

CAUTION:

• If the tool is operated continuously at low speeds for a

long time, the motor will get overloaded, resulting in

tool malfunction.

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing the side handle (Fig. 4)

Always use the side handle to ensure operating safety.

Install the side handle on the tool barrel, then tighten the

handle by turning clockwise at the desired position.

Installing or removing wheel point (Fig. 5 & 6)

Loosen the collet nut and insert the wheel point into the

collet nut. Use the smaller wrench to hold the spindle and

the larger one to tighten the collet nut securely.

The wheel point should not be mounted more than 8 mm

from the collet nut. Exceeding this distance could cause

vibration or a broken shaft.

To remove the wheel point, follow the installation

procedure in reverse.

CAUTION:

• Use the correct size collet cone for the wheel point

which you intend to use.

OPERATION

CAUTION:

• Always hold the tool firmly with one hand on housing

and the other on the side handle.

• Apply light pressure on the tool. Excessive pressure on

the tool will only cause a poor finish and overloading of

the motor.

Turn the tool on without the wheel point making any

contact with the workpiece and wait until the wheel point

attains full speed. Then apply the wheel point to the

workpiece gently. To obtain a good finish, move the tool

in the leftward direction slowly.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

GD0801C GD0811C

Number min

–1

(RPM) min

–1

(RPM)

1 – 2 7,000 – 10,000 1,800 – 2,400

2 – 3 10,000 – 17,000 2,400 – 4,100

3 – 4 17,000 – 24,000 4,100 – 5,800

4 – 5 24,000 – 29,000 5,800 – 7,000

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GD0811C Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info