Bedienungsanleitung Makita GN420C (Seite 9 von 72) (Deutsch, Englisch, Polnisch)

599701

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Indication lamp

Color of the indication lamp means the followings.

Blinking green: Normal status

Blinking red: Need to recharge the battery cartridge

Lighting-up-red: Recharge the battery cartridge.

Nailing cannot be performed due to no remaining

battery capacity.

Blinking orange after blinking green and red

alternately: Fault detection is running. Remove and

reinsert the battery cartridge to reset. If fault detection is

running again, it is malfunction condition. Ask your local

Makita service center to repair it.

Hook

CAUTION:

Always remove the battery when hanging the tool. Do

not hang the tool to your belt.

Fig.12

The hook is convenient for hanging the tool temporarily.

The hook can be set in two positions according to where

the tool will be hung.

To change the hook position, push its feet in from both

sides and shift to another position.

ASSEMBLY

CAUTION:

• Always remove the fuel cell and the battery

cartridge before carrying out any work on the tool.

Loading the nailer

Fig.13

Insert a strip of nails into the slit in the rear of the

magazine. The nails stop at the entrance of the

magazine because of the nail stopper. Unlock the

magazine by pressing the button of the nail stopper to

insert the nails.

Fig.14

Pull the pusher lever with pressing the pusher button all

the way to the rear of the magazine. Then release the

pusher button, and return the pusher lever to the end of

the strip gently.

Removing nails

Fig.15

Pull the pusher lever and push the pusher button to

release the nail supporter, and then return the pusher

lever to the top with pushing the pusher button.

Slide the nails toward the rear of the magazine. The

nails stop at the entrance of the magazine because of

the nail stopper. Unlock the magazine by pressing the

button of the nail stopper to remove the nails.

Changing the magazine (optional accessory)

Fig.16

A magazine with different length is available as optional

accessory.

To change the magazine, loosen the bolt and remove

the magazine. Then install the new magazine. And

fasten the bolt on the magazine.

OPERATION

WARNING:

• Do not touch around the exhaust vent. The

surface will be very hot during or after an

operation. Touching around the exhaust vent may

cause burns or injuries.

CAUTION:

• Make sure all safety systems are in working order

before operation.

Fig.17

1. To drive a nail, place the contact element against

the workpiece.

The fan motor is activated, fuel gas is injected into

combustion chamber and mixed with air by the fan.

Fig.18

2. Hold the contact element pressing firmly and pull

the trigger.

Fuel gas is combusted and the nail is driven.

3. Further driving can be initiated only after both the

contact element and the trigger are released.

Nail-driving of concrete

WARNING:

• Use hardened nails only for concrete.

Using other purposed nails may cause serious

injuries. Do not nail directly on the concrete.

Failure to do so may cause concrete fragments to

fly off or nails to strike back, causing serious

injuries.

• When driving nails, hold the tool so that it stands

upright to the driving surface.

Slanted nail-driving may cause concrete fragments

to fly off or nails to strike back, causing serious

injuries.

• Do not use the tool on the surface that objects

hang from, such as area where hangers for sewer

pipe, dust pipe etc. are set up

Choose and use appropriate nails so that the

penetration amount into concrete ranges 15 mm - 20

mm.

Fig.19

CAUTION:

• Use this tool only for soft concrete built up not so

long before. Using on the hard concrete may

cause nail bending or nail-driving to insufficient

depth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GN420C Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info