Bedienungsanleitung Makita GS6000 (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599703

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

guard lip. An improperly mounted wheel that

projects through the plane of the guard lip cannot be

adequately protected.

c) The guard must be securely attached to the

power tool and positioned for maximum safety,

so the least amount of wheel is exposed towards

the operator. The guard helps to protect the operator

from broken wheel fragments, accidental contact with

wheel and sparks that could ignite clothing.

d) Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-off wheel. Abrasive cut-off wheels are

intended for peripheral grinding, side forces applied

to these wheels may cause them to shatter.

e) Always use undamaged wheel flanges that are

of correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus

reducing the possibility of wheel breakage. Flanges

for cut-off wheels may be different from grinding

wheel flanges.

f) Do not use worn down wheels from larger

power tools. Wheel intended for larger power tool is

not suitable for the higher speed of a smaller tool and

may burst.

Additional Safety Warnings:

17. Be careful not to damage the spindle, the flange

(especially the installing surface) or the lock nut.

Damage to these parts could result in wheel

breakage.

18. Make sure the wheel is not contacting the

workpiece before the switch is turned on.

19. Before using the tool on an actual workpiece, let it

run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced wheel.

20. Use the specified surface of the wheel to perform

the grinding.

21. Do not leave the tool running. Operate the tool

only when hand-held.

22. Do not touch the workpiece immediately after

operation; it may be extremely hot and could burn

your skin.

23. Observe the instructions of the manufacturer for

correct mounting and use of wheels. Handle and

store wheels with care.

24. Use only flanges specified for this tool.

25. Check that the workpiece is properly supported.

26. Pay attention that the wheel continues to rotate

after the tool is switched off.

27. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-

circuit breaker (30 mA) to assure operator safety.

28. Do not use the tool on any materials containing

asbestos.

29. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high

locations.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see the

switch trigger actuates properly and returns to the

“OFF” position when released.

For tool with the lock-on switch

CAUTION:

• Switch can be locked in “ON” position for ease of

operator comfort during extended use. Apply caution

when locking tool in “ON” position and maintain firm

grasp on tool.

To start the tool, simply pull the switch trigger (in the B

direction). Release the switch trigger to stop. For

continuous operation, pull the switch trigger (in the B

direction) and then push in the lock lever (in the A

direction). To stop the tool from the locked position, pull

the switch trigger fully (in the B direction), then release it.

For tool with the lock-off switch

To prevent the switch trigger from accidentally pulled, a

lock lever is provided. To start the tool, push in the lock

lever (in the A direction) and then pull the switch trigger (in

the B direction). Release the switch trigger to stop.

For tool with the lock-on and lock-off switch

To prevent the switch trigger from accidentally pulled, a

lock lever is provided.

To start the tool, push in the lock lever (in the A direction)

and then pull the switch trigger (in the B direction).

Release the switch trigger to stop.

For continuous operation, push in the lock lever (in the A

direction), pull the switch trigger (in the B direction) and

then pull the lock lever (in the C direction).

To stop the tool from the locked position, pull the switch

trigger fully (in the B direction), then release it.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

(Fig. 2)

CAUTION:

• When the wheel cover is positioned for more safety,

tighten the two hex bolts by the strength more than

10 N.m to secure the wheel cover properly.

Installing or removing grinding wheel

CAUTION:

• Before installing grinding wheel, always check that a

blotter part does not have any abnormalities such as

chips or cracks.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GS6000 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info