Bedienungsanleitung Makita GV7000 (Seite 4 von 7) (Englisch, Holländisch)

448461

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

ENGLISH

Explanation of general view

1 Cover

2 Side grip

3 Switch trigger

4 Lock button

5 Speed adjusting dial

6 Lock nut

7 Abrasive disc

8 Rubber pad

9Spindle

10 Lock nut wrench

11 Wrench

12 Limit mark

13 Brush holder cap

14 Screwdriver

SPECIFICATIONS

Model GV7000 GV7000C

Max. capacities

Abrasive disc ............................................................................ 180 mm 180 mm

No load speed (min

-1

) ................................................................. 4,700 2,500 – 4,700

Overall length .............................................................................. 210 mm 210 mm

Net weight ................................................................................... 2.0 kg 2.0 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

ENB048-3

1. Always use eye and ear protection. Other per-

sonal protective equipment such as dust mask,

gloves, helmet and apron should be worn when

necessary. If in doubt, wear the protective equip-

ment.

2. Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

3. Accessories must be rated for at least the speed

recommended on the tool warning label. Wheels

and other accessories running over rated speed

can fly apart and cause injury.

4. Check the backing pad carefully for cracks, dam-

age or deformity before operation. Replace

cracked, damaged or deformed pad immediately.

5. Check that the workpiece is properly supported.

6. Hold the tool firmly.

7. Keep hands away from rotating parts.

8. Make sure abrasive disc is not contacting the

workpiece before the switch is turned on.

9. When sanding metal surfaces, watch out for fly-

ing sparks. Hold the tool so that sparks fly away

from you and other persons or flammable mate-

rials.

10. Do not leave the tool running. Operate the tool

only when hand-held.

11. Pay attention that the wheel continues to rotate

after the tool is switched off.

12. Do not touch the workpiece immediately after

operation; it may be extremely hot and could

burn your skin.

13. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-

circuit breaker (30 mA) to assure operator safety.

14. Do not use the tool on any materials containing

asbestos.

15. Do not use water or grinding lubricant.

16. Ventilate your work area adequately when you

perform sanding operations.

17. Always use the correct dust mask/respirator for

the material and application you are working

with.

18. Ensure that ventilation openings are kept clear

when working in dusty conditions. If it should

become necessary to clear dust, first disconnect

the tool from the main supply (use non metallic

objects) and avoid damaging internal parts.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing side grip (auxiliary handle) & cover

(Fig. 1 & 2)

CAUTION:

Always be sure that the tool is switched off and

unplugged before installing or removing the side grip.

Install the cover, then screw the side grip on the tool

securely. The side grip and the cover can be installed on

either side of the tool. Always be sure that they are

installed securely.

Switch action (Fig. 3)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button.

To stop the tool from the locked position, pull the trigger

fully, then release it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GV7000 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita GV7000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info