Bedienungsanleitung Makita HB500 (Seite 5 von 17) (Englisch, Holländisch)

599955

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

enSure power iS off before working on the maChine

Insertion of pilot pin

• The pilot pin is used to both centre the cutter and to

eject the slug on completion of the cut. It has a ﬂat side

to allow coolant to run down to reach the centre of the

cut where the heat is greatest. Slide the pin through the

hole in the centre of the cutter shank.

fitting the Cutter

• The Quickhitch™ arbor will accept any cutter with a

19mm diameter shank having one or more ﬂats.

To ﬁt a cutter, align it below the Quickhitch™ and twist the

arbor sleeve clockwise against its spring and hold, Fig. 1.

Insert shank of cutter into arbor, push it home and release

the sleeve, Fig.2.

Twist the cutter in the arbor to ensure the ﬂat is engaged

in the locking mechanism, Fig.3.

Turn the sleeve fully anti-clockwise to complete the locking

operation, Fig.4.

To remove the cutter, simply twist the sleeve clockwise

against the spring, the cutter will be ejected.

Mark the position of the hole

• Make sure the workpiece is clean and ﬂat and position the

machine with the pilot over the centre of the hole to be cut.

Fit the saFety strap.

applying Coolant

• Cutting oil ensures longer cutter life and enables the

slug to be ejected cleanly. A 500 ml bottle is included with

every machine.

• Oil will be automatically delivered to the cutter when

the cut commences

• When cutting on vertical surfaces or upside down, cutting

paste, gel or foam is recommended. It is best applied inside

the cutter before drilling.

• Plug the machine into the power socket and the red LED

on the electronic control panel will ﬂash.

FittinG the cutter

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Drill GuarD instructions

Ensure drill unit is isolated from power supply.

Two screws to support the guard in position,

one either side of the drill.

If necessary press the plastic guard guides into

their locating holes on ether side of the motor

cradle

Fit guard to drill as shown.

Secure guard to drill with screws and washers

supplied. DO NOT overtighten the ﬁxing screws,

these should be loose enough to allow the

guard to rise when required. Lower guard to

drilling surface.

When drilling, the guard should always be in

contact with the surface being drilled. As the

drill is lowered, the guard will rise in relation

to the drill.

FittinG the saFety Guard

N.B. Safety strap and guards have been omitted from

the photo’s for clarity.

The supplied safety strap should be used

wherever possible as a safety precaution in the

event of a power failure releasing the magnet;

particularly in situations where the machine is

clamped onto a vertical surface or in an inverted

position.

saFety strap instructions

When the machine has been clamped to the

workpiece in the correct position for drilling,

the strap should be fed through the channel

between the body of the drill and the magnet,

then passed around a substantial part of the

workpiece. The free end should then be passed

through the buckle, pulled tight and locked.

Once the cut is complete, the strap should be

released and the machine supported before the

magnet is disengaged.

FittinG the saFety straP

The cutting oil bottle is held in a sprung bracket

attached to the top of the drill body. Fit the

bracket by removing one of the cap screws from

the top plate and replace the bolt through the

ﬁxing lug on the bottle bracket, tightening the

bolt enough to allow some radial movement of

the bracket. The coolant tube is a push ﬁt into

the self-seal gland at the base of the tap and a

similar ﬁtting on the lower arbor bracket.

FittinG the oil Bottle

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HB500 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info