Bedienungsanleitung Makita HM 1100 (Seite 5 von 8) (Englisch, Holländisch)

448477

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

ENGLISH

Explanation of general view

1Bit grease

2 Bit shank

3Bit

4 Tool holder cover

5 Change ring

6 Side handle

7 Can be swung 360° on the

vertical and secured at any

desired position

8 Secures at eight different

positions back and forth

on the horizontal

9 Clamp nut

10 Loosen

11 Tighten

12 “ON I” button

13 ON

14 OFF

15 Adjusting dial

16 Screwdriver

17 Rear cover

18 Screws

19 Brush holder cap

20 Socket wrench

21 Crank cap

22 Hammer grease

SPECIFICATIONS

Model HM1100 HM1100C

Blows per minute ................................................................. 2,650 1,300 – 2,650

Overall length ....................................................................... 524 mm 524 mm

Net weight ............................................................................ 6.1 kg 6.1 kg

• Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

• Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

safety instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety

glasses and/or face shield. It is also highly

recommended that you wear a dust mask, ear

protectors and thickly padded gloves.

2. Be sure the bit is secured in place before

operation.

3. Under normal operation, the tool is designed

to produce vibration. The screws can come

loose easily, causing a breakdown or acci-

dent. Check tightness of screws carefully

before operation.

4. In cold weather or when the tool has not been

used for a long time, let the tool warm up for

several minutes by operating it under no

load. This will loosen up the lubrication.

Without proper warm-up, hammering opera-

tion is difficult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the tool

in high locations.

6. Hold the tool firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the

tool only when hand-held.

9. Do not point the tool at any one in the area

when operating. The bit could fly out and

injure someone seriously.

10. When chipping into walls, floors or wherever

‘‘live’’ electrical wires may be encountered,

DO NOT TOUCH ANY METAL PARTS OF THE

TOOL!

Hold the tool by the insulated grasping sur-

faces to prevent electric shock if you chip

into a ‘‘live’’ wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Clean the bit shank and apply the bit grease provided

to it before installing the bit. (Fig. 1)

Pull the tool holder cover down all the way and insert

the bit into the tool holder. (Fig. 2-1)

Turn the bit and push it in until it engages. (Fig. 2-2)

Release the tool holder cover. It will return automati-

cally to its original position to secure the bit.

(Fig. 2-3)

After installing, always make sure that the bit is

securely held in place by trying to pull it out.

To remove the bit, pull the tool holder cover down all

the way and pull the bit out.

Bit angle (Fig. 3)

The bit can be secured at 16 different angles. To

change the bit angle, slide the change ring forward,

then turn the change ring to change the bit angle. At

the desired angle, slide the change ring back to the

original position. Then turn the change ring slightly

so that the bit will be secured in place with a little

click.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM 1100 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HM 1100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info