Bedienungsanleitung Makita HM 1100C (Seite 6 von 8) (Englisch, Holländisch)

448478

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Side handle (auxiliary handle) (Fig. 4)

The side handle can be swung 360° on the vertical

and secured at any desired position. It also secures

at eight different positions back and forth on the hori-

zontal. Just loosen the clamp nut to swing the side

handle to a desired position. Then tighten the clamp

nut securely.

Switch action (Fig. 5)

CAUTION:

Before plugging in the tool, always check to see that

the tool is switched off.

To start the tool, push the “ON I” button on the left

side of the tool. To stop the tool, push the “OFF O”

button on the right side of the tool.

Speed change (Fig. 6)

For HM1100C only

The blows per minute can be adjusted between 1,300

and 2,650 BPM just by turning the adjusting dial. This

can be done even while the tool is running. The dial is

marked 1 (lowest speed) to 5 (full speed). Refer to

the table below for the relationship between the num-

ber settings on the adjusting dial and the blows per

minute.

Chipping / Scaling / Demolition (Fig. 7)

Hold the tool firmly with both hands. Turn the tool on

and apply slight pressure on the tool so that the tool

will not bounce around, uncontrolled. Pressing very

hard on the tool will not increase the efficiency.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 8 & 9)

Whenever carbon brushes must be replaced, they cut

out the tool automatically. When this occurs, loosen

the screws which secure the rear cover. Pry up the

rear cover with a screwdriver and remove it. Then

replace both carbon brushes at the same time. Use

only identical carbon brushes.

Lubrication (Fig. 10 & 11)

This tool requires no hourly or daily lubrication

because it has a grease-packed lubrication system.

Lubricate the tool every time the carbon brushes are

replaced.

Run the tool for several minutes to warm it up. Switch

off and unplug the tool. Remove the crank cap using

a socket wrench. Rest the tool on the table with the

bit end pointing upwards. This will allow the old

grease to collect inside the crank housing. Wipe out

the old grease inside and replace with a fresh grease

(30 g). Use only Makita genuine grease (optional

accessory). Filling with more than the specified

amount of grease (approx. 30 g) can cause faulty

hammering action or tool failure. Fill only with the

specified amount of grease. Reinstall the crank cap

and tighten with the socket wrench. Do not tighten

the crank cap excessively. It is made of resin and is

subject to breakage.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by

a Makita Authorized Service Center.

Number on adjusting dial Blows per minute

52,650

42,350

31,950

21,550

11,300

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM 1100C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HM 1100C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info