Bedienungsanleitung Makita HM 1140C (Seite 5 von 16) (Englisch, Holländisch)

448481

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

Explanation of general view

1 Bit grease

2 Bit shank

3 Tool holder cap

4 Tool holder cover

5 Cut in bit shank

6 Notch in tool holder cap

7 Change ring

8 Side handle

9 Can be swung 360° on the

vertical and secured at any

desired position

10 Secures at eight different

positions back and forth

on the horizontal

11 Clamp nut

12 Loosen

13 Tighten

14 “ON I” button

15 ON

16 OFF

17 Adjusting dial

18 Screwdriver

19 Rear cover

20 Screws

21 Brush holder cap

22 Socket wrench

23 Crank cap

24 Hammer grease

SPECIFICATIONS

Model HM1140C

Blows per minute ........................................1,300 – 2,650

Overall length ..................................................... 517mm

Net weight ...............................................................6.3 kg

• Due to the continuing program of research and devel-

opment, the specifications herein are subject to change

without prior notice.

• Note: Specifications may differ from country to country.

Power supply

The machine should be connected only to a power sup-

ply of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with European

Standard and can, therefore, also be used from sockets

without earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear protec-

tors and thickly padded gloves.

2. Be sure the bit is secured in place before opera-

tion.

3. Under normal operation, the machine is

designed to produce vibration. The screws can

come loose easily, causing a breakdown or acci-

dent. Check tightness of screws carefully before

operation.

4. In cold weather or when the machine has not

been used for a long time, let the machine warm

up for several minutes by operating it under no

load. This will loosen up the lubrication. Without

proper warm-up, hammering operation is diffi-

cult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the machine

in high locations.

6. Hold the machine firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the machine running. Operate the

machine only when hand-held.

9. Do not point the machine at any one in the area

when operating. The bit could fly out and injure

someone seriously.

10. When chipping into walls, floors or wherever

“live” electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE

MACHINE!

Hold the machine by the insulated grasping sur-

faces to prevent electric shock if you chip into a

“live” wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing bit

Important:

Always be sure that the machine is switched off and

unplugged before installing or removing the bit.

This machine accepts 3/4” Hexagonal and 21/32” round

shank bits. Clean the bit shank and apply the bit grease

provided to it before installing the bit. (Fig. 1)

Pull the tool holder cover down all the way. (Fig. 2-1)

With the cut in the bit shank aligned with the notch in the

tool holder cap, insert the bit into the tool holder. (Fig.2-2)

Release the tool holder cover. It will return automatically to

its original position to secure the bit. (Fig. 2-3)

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the tool holder cover down all the

way and pull the bit out.

Bit angle (Fig. 3)

The bit can be secured at 12 different angles. To change

the bit angle, slide the change ring forward, then turn the

change ring to change the bit angle. At the desired angle,

slide the change ring back to the original position. Then

turn the change ring slightly so that the bit will be secured

in place with a little click.

Side handle (auxiliary handle) (Fig. 4)

The side handle can be swung 360° on the vertical and

secured at any desired position. It also secures at eight

different positions back and forth on the horizontal. Just

loosen the clamp nut to swing the side handle to a

desired position. Then tighten the clamp nut securely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM 1140C Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HM 1140C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info