Bedienungsanleitung Makita HM 1200 (Seite 5 von 7) (Englisch, Holländisch)

448484

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

OPERATING INSTRUCTIONS

Installing or removing bull point or other bits

(cold chisel, etc.)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

For HM1200 (Fig. 1)

Pivot the tool retainer to the side. (If it is difficult to move

the tool retainer with your thumbs, tap it with a hammer.)

Insert the bit into the tool barrel as far as it will go. Return

the tool retainer to its original position to secure the bit.

To remove the bit, follow the installation procedure in

reverse.

For HM1200B & HM1200K (Fig. 2)

Pull out and turn the tool retainer 180 degrees (1/2 turn).

Then insert the bit into the tool holder with the notched

portion on the bit facing back toward the tool retainer.

Then pull out and turn back the tool retainer 180 degrees

to secure the bit. Try to pull the bit out of the tool holder to

make sure the retained bit before use.

CAUTION:

Never use B-type shank bits. They can cause damage to

the tool. (For HM1200B)

Side grip/Side handle (auxiliary handle)

For HM1200 (Standard type) (Fig. 3)

The side grip swings around to either side, allowing easy

handling of the tool in any position. Loosen the side grip

by turning it counterclockwise, swing it to the desired

position and then tighten it by turning clockwise.

For HM1200 (European type), HM1200B & HM1200K

(Fig. 4)

The side handle swings around 360° on the vertical as

well as back and forth on the horizontal. Turn the clamp

nut clockwise to secure the handle in the desired position.

Switch action (Fig. 5)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

• Do not tape, tie or otherwise secure the trigger in the

“ON” position.

To start the tool, simply pull the trigger. Release the trig-

ger to stop.

Chipping / Scaling / Demolition

Hold the tool firmly with both hands. Turn the tool on and

apply slight pressure on the tool so that the tool will not

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 6 & 7)

Whenever carbon brushes must be replaced, they cut out

the tool automatically. When this occurs, replace both

carbon brushes at the same time. Use only identical car-

bon brushes.

Lubrication (Fig. 8)

This tool requires no hourly or daily lubrication because it

has a grease-packed lubrication system. Lubricate the

tool every time the carbon brushes are replaced.

Run the tool for several minutes to warm it up. Switch off

and unplug the tool. Remove the crank cap using a Mak-

ita lock nut wrench 35 (optional accessory). Rest the tool

on the table with the bit end pointing upwards. This will

allow the old grease to collect inside the crank housing.

Wipe out the old grease inside and replace with a fresh

grease (30 g). Use only Makita genuine grease (optional

accessory). Filling with more than the specified amount

of grease (approx. 30 g) can cause faulty hammering

action or tool failure. Fill only with the specified amount of

grease. Reinstall the crank cap and tighten with the lock

nut wrench. Do not tighten the crank cap excessively. It is

made of resin and is subject to breakage.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Centre.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM 1200 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HM 1200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info