Bedienungsanleitung Makita hm 1202 c (Seite 6 von 44) (Deutsch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388900

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ENGLISH

Explanation of general view

1 Bit grease

2 Bit shank

3 Tool holder cover

4Bit

5 Change ring

6 Side handle (auxiliary handle)

7 Can be swung 360° on the

vertical and secured at any

desired position

8 Secures at eight different

positions back and forth

on the horizontal

9 Clamp nut

10 Loosen

11 Tighten

12 Side handle base

13 Switch lever

14 ON

15 OFF

16 Adjusting dial

17 Power-ON indicator lamp

(green)

18 Service indicator lamp (red)

19 Screwdriver

20 Rear cover

21 Screws

22 Brush holder cap

23 Screws

24 Handle

25 Socket wrench

26 Crank cap

27 Hammer grease

SPECIFICATIONS

Model HM1202 HM1202C

Blows per minute ......................................................................... 1,900 950 – 1,900

Overall length .............................................................................. 578 mm 578 mm

Net weight ................................................................................... 9.3 kg 9.3 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

For public low-voltage distribution systems of

between 220 V and 250 V

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.46 Ohms it can be presumed that

there will be no negative effects.

The mains socket used for this device must be protected

with a fuse or protective circuit breaker having slow trip-

ping characteristics.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

ENB009-1

1. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring or its own cord. Con-

tact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Wear ear protectors when using the tool for

extended periods. Prolonged exposure to high

intensity noise can cause hearing loss.

3. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask and thickly

padded gloves.

4. Be sure the bit is secured in place before opera-

tion.

5. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

6. In cold weather or when the tool has not been

used for a long time, let the tool warm up for a

while by operating it under no load. This will

loosen up the lubrication. Without proper warm-

up, hammering operation is difficult.

7. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

8. Hold the tool firmly with both hands.

9. Keep hands away from moving parts.

10. Do not leave the tool running. Operate the tool

only when hand-held.

11. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

12. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Clean the bit shank and apply the bit grease provided

to it before installing the bit. (Fig. 1)

Pull the tool holder cover down all the way. (Fig. 2)

Insert the bit into the tool. Turn the bit and push it in

until it engages. (Fig. 3-1)

Release the tool holder cover. It will return automati-

cally to its original position to secure the bit.

(Fig. 3-2)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita hm 1202 c Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita hm 1202 c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info