Bedienungsanleitung Makita HM 1213C (Seite 6 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448488

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Loosen the six screws and remove the handle. Note that

the top screws are different from other screws. (Fig. 12)

Disconnect the connector by pulling them. (Fig. 13)

Loosen the four screws on crank cap and remove the

crank cap cover. (Fig. 14)

Wipe out the old grease inside and replace with a fresh

grease (60 g). Use only Makita genuine hammer grease

(optional accessory). Filling with more than the specified

amount of grease (approx. 60 g) can cause faulty

hammering action or tool failure. Fill only with the

specified amount of grease. (Fig. 15)

CAUTION:

• Be careful not to damage the connector or lead wires

especially when wiping out the old grease.

To reassemble the tool, follow the disassembling

procedure in reverse.

CAUTION:

• Do not tighten the crank cap excessively. It is made of

resin and is subject to breakage. (Fig. 16)

Connect the connector firmly and then reinstall the

handle.

CAUTION:

• Be careful not to damage the connector or lead wires

especially when installing the handle.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Bull point (SDS-max)

• Cold chisel (SDS-max)

• Scaling chisel (SDS-max)

• Clay spade (SDS-max)

• Bit grease

• Safety goggles

• Hammer grease

• Plastic carrying case

For Model HM1213C

For European countries only

Noise

ENG102-2

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 75 dB (A)

Sound power level (L

): 95 dB (A)

Uncertainty (K): 2.5 dB (A)

Wear ear protection

Vibration

ENG216-1

The vibration total value (tri-axial vector sum) determined

according to EN60745-2-6:

Work mode: chiseling function with side handle

Vibration emission (a

h,CHeq

): 7.0 m/s

Uncertainty (K): 1.5 m/s

For Model HM1203C

For European countries only

Noise

ENG102-2

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 81 dB (A)

Sound power level (L

): 95 dB (A)

Uncertainty (K): 2 dB (A)

Wear ear protection

Vibration

ENG216-1

The vibration total value (tri-axial vector sum) determined

according to EN60745-2-6:

Work mode: chiseling function with side handle

Vibration emission (a

h,CHeq

): 15.5 m/s

Uncertainty (K): 1.5 m/s

EC Declaration of Conformity ENH213-1

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machin(s):

Designation of Machine: Demolition Hammer

Model No./ Type: HM1213C, HM1203C

are of series production and

Conforms to the following European Directives:

2000/14/EC, 98/37/EC until 28th December 2009 and

then with 2006/42/EC from 29th December 2009

And are manufactured in accordance with the following

standards or standardised documents:

EN60745

The technical documentation is kept by our authorised

representative in Europe who is:

Makita International Europe Ltd,

Michigan, Drive, Tongwell,

Milton Keynes, MK15 8JD, England

The conformity assessment procedure required by

Directive 2000/14/EC was in Accordance with annex VIII.

Notified Body:

TÜV Rheinland Product Safety GmbH, identification

no. 0197

Model HM1213C

Measured Sound Power Level: 95 dB

Guaranteed Sound Power Level: 97 dB

Model HM1203C

Measured Sound Power Level: 95 dB

Guaranteed Sound Power Level: 98 dB

16th January 2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM 1213C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info