Bedienungsanleitung Makita HM 1400K (Seite 4 von 32) (Deutsch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448498

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH

Explanation of general view

1Bolts

2Grip

3 Notched portion

4 Tool retainer

5Switch lever

6 Handle

7 Holder cap plate

8Screwdriver

9 Brush holder cap

10 Plate 50

11 Hammer grease

SPECIFICATIONS

Model HM1400 HM1400K

Blows per minute ....................................................................................... 1,200 1,200

Overall length ............................................................................................ 613 mm 600 mm

Net weight ................................................................................................. 17 kg 17 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

be operated on single-phase AC/DC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear protec-

tors and thickly padded gloves.

2. Be sure the bit is secured in place before opera-

tion.

3. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

4. In cold weather or when the tool has not been

used for a long time, let the tool warm up for sev-

eral minutes by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is difficult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

6. Hold the tool firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

10. When chipping into walls, floors or wherever

“live” electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE TOOL!

Hold the tool by the insulated grasping surfaces

to prevent electric shock if you chip into a “live”

wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing grip (Fig. 1)

Install the grip securely with the bolts using the hex

wrench.

Installing or removing bull point or other bits

(cold chisel, etc.) (Fig.2&3)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Turn up the tool retainer. With the notched portion of the

bit facing the tool retainer, insert the bit into the tool bar-

rel as far as it will go.

Return the tool retainer to its original position to secure

the bit.

To remove the bit, follow the installation procedure in

reverse.

Switch action (Fig. 4)

CAUTION:

• Before plugging in the tool, always check to see that

the switch lever actuates properly and returns to the

“OFF” position when released.

• Do not tape, tie or otherwise secure the switch lever in

the “ON” position.

To start the tool, simply squeeze the switch lever.

Release the switch lever to stop.

Chipping/ Scaling / Demolition

Hold the tool firmly with both hands. Turn the tool on and

apply slight pressure on the tool so that the tool will not

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM 1400K Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HM 1400K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info