Bedienungsanleitung Makita HM0810B (Seite 4 von 32) (Deutsch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

599545

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH

Explanation of general view

1 Bull point

2 Tool retainer

3Cap

4 Red dot (Tool holder)

5 Red dot (Tool retainer)

6 Tool retainer

7 Press in

8 Turn 180°

9 Side grip

10 Lock button

11 Switch trigger

12 Hex wrench

13 Rear cover

14 Screwdriver

15 Brush holder cap

16 Lock nut wrench

17 Crank cap

SPECIFICATIONS

Model HM0810 HM0810B

Blows per minute......................................................................................................................2,900 2,900

Overall length ...........................................................................................................................410 mm 433 mm

Net weight ................................................................................................................................5.3 kg 5.3 kg

• Due to our continuing programme of research and

development, the specifications herein are subject to

change without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed Safety

instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear protec-

tors and thickly padded gloves.

2. Be sure the bit is secured in place before opera-

tion.

3. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

4. In cold weather or when the tool has not been

used for a long time, let the tool warm up for sev-

eral minutes by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is difficult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

6. Hold the tool firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

10. When chipping into walls, floors or wherever

“live” electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE TOOL!

Hold the tool by the insulated grasping surfaces to

prevent electric shock if you chip into a “live” wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM0810B Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info