Bedienungsanleitung Makita HM0810T (Seite 5 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

599546

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing side grip (auxiliary handle) (Fig. 2)

The side grip swings around to either side, allowing easy

handling of the tool in any position. Loosen the side grip

by turning it counterclockwise, swing it to the desired

position and then tighten it by turning clockwise.

Bit grease (optional accessory)

Coat the bit shank head beforehand with a small amount

of bit grease (about 0.5 – 1 g; 0.02 – 0.04 oz.). This

chuck lubrication assures smooth action and longer serv-

ice life.

Installing or removing bit (Fig. 3 & 4)

Pull the change ring down all the way and insert the bit

into the tool holder as far as it will go. Release the

change ring and it will return automatically to its original

position to secure the bit. After installing, always make

sure that the bit is securely held in place by trying to pull

it out.

To remove the bit, pull the change ring down all the way

and pull the bit out.

OPERATION

Chipping / Scaling / Demolition

Hold the tool firmly with both hands. Turn the tool on and

apply slight pressure on the tool so that the tool will not

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 5, 6 & 7)

When the resin insulating tip inside the carbon brush is

exposed to contact the commutator, it will automatically

shut off the motor. When this occurs, both carbon

brushes should be replaced. Keep the carbon brushes

clean and free to slip in the holders. Both carbon brushes

should be replaced at the same time. Use only identical

carbon brushes.

Use a hex wrench to remove the rear cover.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

Lubrication (Fig. 8 & 9)

This tool requires no hourly or daily lubrication because it

has a grease-packed lubrication system. It should be

relubricated after every 6 months of operation. Send the

complete tool to Makita Authorized or Factory Service

Center for this lubrication service. However, if circum-

stances require that you should lubricate it by yourself,

proceed as follows.

Run the tool for several minutes to warm it up. Switch off

and unplug the tool.

Remove the crank cap using a Makita lock nut wrench 35

(optional accessory). Rest the tool on the table with the

bit end pointing upwards. This will allow the old grease to

collect inside the crank housing.

Wipe out the old grease inside and replace with a fresh

grease (30 g; 1 oz). Use only Makita genuine hammer

grease (optional accessory). Filling with more than the

specified amount of grease (approx. 30 g; 1 oz) can

cause faulty hammering action or tool failure. Fill only

with the specified amount of grease.

Reinstall the crank cap and tighten with the lock nut

wrench.

CAUTION:

• Do not tighten the crank cap excessively. It is made of

resin and is subject to breakage.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Bull point

• Cold chisel

• Scaling chisel

• Clay spade

• Grooving chisel

• Rammer

• Bushing tool

• Ground rod adapter

• Lock nut wrench

•Hex wrench

• Safety goggle

• Hammer grease

• Carrying case

• Bit grease

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM0810T Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info