Bedienungsanleitung Makita HR 1830 (Seite 5 von 40) (Deutsch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78635

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop. For continuous opera-

tion, pull the switch trigger and then push in the lock but-

ton. To stop the tool from the locked position, pull the

switch trigger fully, then release it.

Lighting up the lamps (Fig. 2)

For Model HR1830F only

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the lamp, pull the trigger. Release the trigger

to turn it off.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

Reversing switch action (Fig. 3)

This tool has a reversing switch to change the direction of

rotation. Move the reversing switch lever to the posi-

tion (A side) for clockwise rotation or the position (B

side) for counterclockwise rotation.

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• If the switch trigger can not be depressed, check to see

that the reversing switch is fully set to position (A

side) or (B side).

Selecting action mode (Fig. 4)

This tool employs an action mode changing knob. Select

one of the two modes suitable for your work needs by

using this knob.

For rotation only, depress the lock button and turn the

knob so that the arrow on the knob points toward the

symbol on the tool body.

For rotation with hammering, depress the lock button and

turn the knob so that the arrow on the knob points toward

the symbol on the tool body.

CAUTION:

• Always set the knob fully to your desired mode symbol.

If you operate the tool with the knob positioned half-

way between the mode symbols, the tool may be dam-

aged.

• Use the knob after the tool comes to a complete stop.

Torque limiter

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

CAUTION:

• As soon as the torque limiter actuates, switch off the

tool immediately. This will help prevent premature wear

of the tool.

• Hole saws cannot be used with this tool. They tend to

pinch or catch easily in the hole. This will cause the

torque limiter to actuate too frequently.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Side grip (auxiliary handle) (Fig. 5)

CAUTION:

• Always use the side grip to ensure operating safety.

Install the side grip so that the teeth on the grip fit in

between the protrusions on the tool barrel. Then tighten

the grip by turning clockwise at the desired position. It

may be swung 360° so as to be secured at any position.

Bit grease

Coat the bit shank head beforehand with a small amount

of bit grease (about 0.5 – 1 g).

This chuck lubrication assures smooth action and longer

service life.

Installing or removing the bit

Clean the bit shank and apply bit grease before installing

the bit. (Fig. 6)

Insert the bit into the tool. Turn the bit and push it in until

it engages. (Fig. 7)

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the way

and pull the bit out. (Fig. 8)

Depth gauge (Fig. 9)

The depth gauge is convenient for drilling holes of uni-

form depth. Loosen the side grip and insert the depth

gauge into the hole in the side grip. Adjust the depth

gauge to the desired depth and tighten the side grip.

NOTE:

• The depth gauge cannot be used at the position where

the depth gauge strikes against the gear housing.

Dust cup (Fig. 10)

Use the dust cup to prevent dust from falling over the tool

and on yourself when performing overhead drilling opera-

tions. Attach the dust cup to the bit as shown in Fig. 10.

The size of bits which the dust cup can be attached to is

as follows.

Bit diameter

Dust cup 5 6 mm – 14.5 mm

Dust cup 9 12 mm – 16 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR 1830 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HR 1830

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info