Bedienungsanleitung Makita hr 2400 (Seite 4 von 12) (Englisch, Holländisch)

388817

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Adjusting depth of drilling (Fig. 4)

Loosen the wing bolt and adjust the depth gauge to the

desired depth. After adjusting, tighten the wing bolt.

NOTE:

The depth gauge cannot be used at the position where

the depth gauge strikes against the gear housing.

Side grip (Auxiliary handle) (Fig. 4)

The side grip swings around to either side, allowing easy

handling of the tool in any position. Loosen the wing bolt

on the side grip and swing the side grip to the desired

position. Then tighten the wing bolt to secure the side

grip.

Operating instruction (Fig. 5)

Important:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

Switching ON and OFF (Fig. 5)

To switch on, press the trigger.

To switch off, release the trigger.

Continuous running (Fig. 5)

Press the trigger and at the same time slide the lock lever

upward. To stop from this lock position, press the trigger

and release it.

Variable trigger speed control (Fig. 5)

The speed varies from 0 to maximum, depending on the

pressure applied to the trigger. The more the trigger is

pressed, the faster the tool runs.

Reversing switch (Fig. 5)

Important:

Only reverse the direction of rotation when the motor

stops completely.

To change the direction of rotation:

Position FWD: right hand rotation

Position REV: left hand rotation

Three selecting action modes (Fig. 6)

For hammer drilling:

Turn the knob so that the arrow points toward the

symbol.

For drilling only:

Turn the knob so that the arrow points toward the

symbol.

For hammering only:

Turn the knob so that the arrow points toward the

symbol.

NOTE:

When it is hard to turn the knob, pull the switch trigger

half-way for running at low speed and turn the knob.

Torque limiter

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

CAUTION:

As soon as the torque limiter actuates, switch off the tool

immediately. This will help prevent premature wear of the

tool. Hole saws, core bit, diamond core bit, etc. cannot be

used with this tool. They tend to pinch or catch easily in

the hole. This will cause the torque limiter to actuate too

frequently.

Using cold chisel or bull point (Fig. 7)

1. Disconnect plug.

2. Remove the side grip from the tool.

3. Turn the knob to hammer drilling symbol .

4. Install the cold chisel or bull point and then the chisel

adapter (optional accessory) on the tool.

5. Rotate the cold chisel toward the direction suitable

for your work. Then secure the cold chisel and chisel

adapter by using the clamp screw on the chisel

adapter.

6. Turn the knob to hammering only symbol . Now

you can use the cold chisel or bull point.

NOTE:

Always set “hammering only” action when using the cold

chisel or bull point. If you use “hammer drilling” or “drilling

only” action, the hammering mechanism may be dam-

aged on the tool.

Drilling in wood or metal (Fig. 8)

Use the optional drill chuck assembly (consisting of drill

chuck and chuck adapter assembly). When installing it,

refer to “installing or removing drill bit” described on the

previous page. Set the knob to “drilling only”. You can drill

up to 13 mm diameter in metal and up to 38 mm diame-

ter in wood. (Note: When using a flat boring bit.)

NOTE:

Never set “hammer drilling” action when using the drill

chuck assembly because it may be damaged and come

off when reversing the tool.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita hr 2400 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita hr 2400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info