Bedienungsanleitung Makita HR 2410X (Seite 6 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448524

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Depth gauge (Fig. 5)

The depth gauge is convenient for drilling holes of uni-

form depth. Insert the depth gauge into the hole in the

grip base. Adjust the depth gauge to the desired depth

and then tighten the clamp screw to secure the depth

gauge.

NOTE:

The depth gauge cannot be used at the position where

the depth gauge strikes against the gear housing.

Switch action (Fig. 6)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

Reversing switch action (Fig. 6)

For Model HR2410 and HR2410X

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• Do not pull the switch trigger when the reversing switch

lever is in the neutral position. If you pull the trigger

forcibly, the switch may be damaged.

This tool has a reversing switch to change the direction of

rotation. Move the lever to the

p position for clockwise

rotation or the

q position for counterclockwise rotation.

Selecting action mode (Fig. 7)

This tool employs an action mode changing knob. Select

one of the two modes suitable for your work needs by

using this knob. For rotation only, turn the knob so that

the arrow on the knob points toward the

M symbol on

the tool body. For rotation with hammering, turn the knob

so that the arrow on the knob points toward the

r sym-

bol on the tool body.

CAUTION:

Always set the knob fully to your desired mode symbol. If

you operate the tool with the knob positioned half-way

between the mode symbols, the tool may be damaged.

Torque limiter

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

CAUTION:

• As soon as the torque limiter actuates, switch off the

tool immediately. This will help prevent premature wear

of the tool.

• Hole saws, core bits, diamond core bits, etc. cannot be

used with this tool. They tend to pinch or catch easily in

the hole. This will cause the torque limiter to actuate

too frequently.

Hammer drilling operation

Position the bit at the desired location for the hole, then

pull the trigger.

Do not force the tool. Light pressure gives best results.

Keep the tool in position and prevent it from slipping away

from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at an

idle, then remove the bit partially from the hole. By

repeating this several times, the hole will be cleaned out

and normal drilling may be resumed.

CAUTION:

There is tremendous and sudden twisting force exerted

on the tool/bit at the time of hole breakthrough, when the

hole becomes clogged with chips and particles, or when

striking reinforcing rods embedded in the concrete.

Always use the side grip (auxiliary handle) and firmly

hold the tool by both side grip and switch handle during

operations. Failure to do so may result in the loss of con-

trol of the tool and potentially severe injury.

Bit grease

Coat the bit shank head beforehand with a small amount

of bit grease (about0.5–1g).

This chuck lubrication assures smooth action and longer

service life.

Blow-out bulb (Fig. 8)

Use the blow-out bulb to clean out the hole.

Dust cup (Fig. 9)

Use the dust cup to prevent dust from falling over the tool

and on yourself when performing overhead drilling opera-

tions. Attach the dust cup to the bit as shown in Fig. 9.

The size of bits which the dust cup can be attached to is

as follows.

Drilling in wood or metal (Fig. 10 & 11)

Use the optional drill chuck assembly (standard equip-

ment for Model HR2410X). When installing it, refer to

“Installing or removing drill bit” described on the previous

page.

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as it

will go. Hold the ring firmly and turn the sleeve clockwise

to tighten the chuck.

To remove the bit, hold the ring and turn the sleeve coun-

terclockwise. Set the action mode changing knob to

“rotation only”. You can drill up to 13 mm diameter in

metal and up to 32 mm diameter in wood.

Bit diameter (mm)

Dust cup 5 6 – 14.5

Dust cup 9 12 – 16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR 2410X Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HR 2410X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info