Bedienungsanleitung Makita hr 2413 (Seite 5 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388815

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

ENGLISH

Explanation of general view

1Tighten

2Loosen

3 Side grip

4 Bit shank

5 Bit grease

6Bit

7 Chuck cover

8 Clamp screw

9 Depth gauge

10 Switch trigger

11 Reversing switch lever

12 Action mode changing knob

13 Blow-out bulb

14 Dust cup

15 Chuck adapter

16 Keyless drill chuck

17 Sleeve

18 Ring

19 Tighten

20 Loosen

21 Wrench

22 Soft jaws

23 Screw

SPECIFICATIONS

Model HR2410/HR2410X HR2413

Capacities

Concrete ................................................................................... 24 mm 24 mm

Wood ........................................................................................ 32 mm 32 mm

Steel ......................................................................................... 13 mm 13 mm

No load speed (min

-1

) .................................................................. 0 – 1,050 0 – 1,050

Blows per minute ......................................................................... 0 – 4,900 0 – 4,900

Overall length .............................................................................. 371 mm 371 mm

Net weight .................................................................................... 2.4 kg 2.3 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for hammer drilling and drilling in

brick, concrete and stone. It is also suitable for drilling

without impact in wood, metal, ceramic and plastic.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear protec-

tors and thickly padded gloves.

2. Be sure the bit is secured in place before opera-

tion.

3. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

4. In cold weather or when the tool has not been

used for a long time, let the tool warm up for sev-

eral minutes by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is difficult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

6. Hold the tool firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

10. When drilling or chipping into walls, floors or

wherever “live” electrical wires may be encoun-

tered, DO NOT TOUCH ANY METAL PARTS OF

THE TOOL!

Hold the tool by the insulated grasping surfaces

to prevent electric shock if you drill or chip into a

“live” wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Side grip (auxiliary handle) (Fig. 1)

The side grip swings around to either side, allowing easy

handling of the tool in any position. Loosen the side grip

by turning it counterclockwise, swing it to the desired

position and then tighten it by turning clockwise.

Installing or removing drill bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Clean the bit shank and apply bit grease before installing

the bit. (Fig. 2)

Insert the bit into the tool. Turn the bit and push it in until

it engages. (Fig. 3)

If the bit cannot be pushed in, remove the bit. Pull the

chuck cover down a couple of times. Then insert the bit

again. Turn the bit and push it in until it engages. (Fig. 4)

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the way

and pull the bit out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita hr 2413 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita hr 2413

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info