Bedienungsanleitung Makita HR 2432 (Seite 8 von 18) (Englisch, Holländisch)

78785

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Bit grease (optional accessory)

Coat the bit shank head beforehand with a small amount

of bit grease (about 0.5 – 1 g).

This chuck lubrication assures smooth action and longer

service life.

Installing or removing the bit

Clean the bit shank and apply bit grease before installing

the bit. (Fig. 7)

Insert the bit into the tool. Turn the bit and push it in until

it engages.

After installing, always make sure that the bit is securely

held in place by trying to pull it out. (Fig. 8)

To remove the bit, pull the chuck cover down all the way

and pull the bit out. (Fig. 9)

Bit angle (when chipping, scaling or demolishing)

The bit can be secured at the desired angle. To change

the bit angle, depress the lock button and rotate the

action mode changing knob to the

O symbol. Turn the

bit to the desired angle. (Fig. 10)

Depress the lock button and rotate the action mode

changing knob to the symbol. Then make sure that

the bit is securely held in place by turning it slightly.

(Fig. 11)

Depth gauge (optional accessory) (Fig. 12)

When drilling without dust extractor attachment, the

depth gauge is convenient for drilling holes of uniform

depth. Remove the dust extractor attachment. Loosen

the side grip and insert the depth gauge into the hole in

the side grip. Adjust the depth gauge to the desired depth

and tighten the side grip.

NOTE:

• The depth gauge cannot be used at the position where

the depth gauge strikes against the gear housing.

Dust extractor attachment and dust bag

(In concrete drilling operation)

With the dust extractor attachment and the dust bag

installed on this tool, you can do your work very cleanly

without dust scattered around in the work site.

CAUTION:

• These two accessories can be used only for drilling

holes in concrete. Accordingly, do not use them in

metal or wood drilling operation.

Dust cup (optional accessory) (Fig. 13)

Use the dust cup to prevent dust from falling over the tool

and on yourself when performing overhead drilling opera-

tions. Attach the dust cup to the bit as shown in the fig-

ure. The size of bits which the dust cup can be attached

to is as follows.

Installing dust extractor attachment

Loosen the clamp screw of the side grip by turning it

counterclockwise. Insert the coupling rod of the dust

extractor attachment through the coupling hole of the

side grip until the rod cannot be pushed in any further.

And then tighten the clamp screw clockwise to secure the

dust extractor attachment. The coupling rod can be

inserted from either side A or B. (Fig. 14)

NOTE:

• At some angles of the side grip with the tool, the dust

extractor attachment cannot be installed on the tool

because of the interference between the attachment

and the tool.

Insert firmly the hose of the dust extractor attachment

into the hose port of the tool until the hose hits against

the bottom of the port to be fixed firmly to the tool.

(Fig. 15)

Installing dust bag (Fig. 16)

Keeping the angle of the dust bag with the tool at 90°,

insert the dust bag into the dust exhaust port of the tool.

Secure the dust bag by turning it clockwise at its frame.

Adjusting the position of dust extractor

attachment

Loosen the clamp screw of the dust extractor attachment

by turning it counterclockwise. (Fig. 17)

And then align the tip of the bit with the top of the dust

extractor attachment. Tighten the clamp screw by turning

it clockwise to secure the dust extractor attachment.

(Fig. 18)

Depth adjustment (Fig. 19)

Loosen the screw of the stopper by turning it counter-

clockwise so that the stopper could slide on the depth

gauge of the dust extractor attachment. Slide the stopper

to the desired drilling depth of the gauge, and then

tighten the screw by turning it clockwise.

OPERATION

Drilling with dust extractor attachment (Fig. 20)

In drilling operation, hold the tool so that the top end of

the dust extractor attachment is always kept in complete

contact with the surface of concrete.

NOTE:

• Any space between them would result in a consider-

able loss of dust extracting power.

Cleaning out dust bag (Fig. 21)

Remove the dust bag from the tool. Pull the fastener out

of the dust bag, and then remove dust or particles to

clean out the dust bag.

NOTE:

• Too much dust in the dust bag would result in a consid-

erable loss of dust extracting power. Accordingly, clean

out the dust bag from time to time.

Drilling without dust extractor attachment

(Fig. 22)

This tool can be also used as a standard rotary hammer

without the dust extractor attachment and the dust bag.

Before drilling operation without the dust extractor attach-

ment and the dust bag, plug the hose port with the cap

provided. The cap reduces the exhaust air from the dust

exhaust port for your comfortable operation.

Bit diameter

Dust cup 5 6 mm – 14.5 mm

Dust cup 9 12 mm – 16 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR 2432 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HR 2432

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info