Bedienungsanleitung Makita HR 3541FC (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448539

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

Lighting up the lamp

For Model HR3541FC (Fig. 2)

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to turn on the light. The lamp keeps

on lighting while the switch trigger is being pulled.

The lamp turns off 10 - 20 seconds after releasing the

trigger.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp.

Be careful not to scratch the lens of lamp, or it may

lower the illumination.

Speed change (Fig. 3)

The revolutions and blows per minute can be adjusted just

by turning the adjusting dial. The dial is marked 1 (lowest

speed) to 5 (full speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the revolutions/

blows per minute.

CAUTION:

• If the tool is operated continuously at low speeds for a

long time, the motor will get overloaded, resulting in

tool malfunction.

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

Selecting the action mode

Rotation with hammering (Fig. 4)

For drilling in concrete, masonry, etc., depress the lock

button and rotate the change lever so that the pointer

points to the symbol. Use a tungsten-carbide tipped

bit.

Rotation only (Fig. 5)

For drilling in wood or metal, materials, etc., depress the

lock button and rotate the change lever so that the pointer

points to the symbol. Use a twist drill bit or wood bit.

Hammering only (Fig. 6)

For chipping, scaling or demolition operations, depress

the lock button and rotate the change lever so that the

pointer points to the symbol. Use a bull point, cold

chisel, scaling chisel, etc.

CAUTION:

• Do not rotate the change lever when the tool is running

under load. The tool will be damaged.

• To avoid rapid wear on the mode change mechanism,

be sure that the change lever is always positively

located in one of the three action mode positions.

Torque limiter

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

CAUTION:

• As soon as the torque limiter actuates, switch off the

tool immediately. This will help prevent premature wear

of the tool.

Indicator lamp (Fig. 7)

The green power-ON indicator lamp lights up when the

tool is plugged. If the indicator lamp does not light up, the

main cord or the controller may be defective. The indicator

lamp is lit but the tool does not start even if the tool is

switched on, the carbon brushes may be worn out, or the

controller, the motor or the ON/OFF switch may be

defective.

The red service indicator lamp lights up when the carbon

brushes are nearly worn out to indicate that the tool needs

servicing. After approx. 8 hours of use, the motor will

automatically be shut off.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Number on

adjusting dial

Revolutions per

minute

Blows per minute

5 630 3,300

4 590 3,100

3 480 2,500

2 370 1,900

1 315 1,650

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR 3541FC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info