Bedienungsanleitung Makita HR 3850K (Seite 5 von 10) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448535

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

ENGLISH

Explanation of general view

1 Side grip

2 Grip base

3 Red dot (Tool holder)

4 Red dot (Tool retainer)

5 Tool retainer

6 Press in

7 Turn 180°

8 Change lever

9 For rotation with hammering

10 For hammering only

11 Wing bolt

12 Depth gauge

13 Switch trigger

14 Core bit

15 Adapter

16 Center bit

17 Rod

18 Hex wrench

19 Rear cover

20 Screwdriver

21 Brush holder cap

22 Lock nut wrench

23 Crank cap

24 Hammer grease

SPECIFICATIONS

Model HR3520B HR3850B HR3850K

Capacities

Tungsten-carbide bit ....................................................................... 35 mm 38 mm 38 mm

Core bit ........................................................................................... 79 mm 118 mm 118 mm

No load speed (min

–1

) ....................................................................... 440 240 240

Blows per min. ................................................................................... 3,300 2,900 2,900

Overall length .................................................................................... 400 mm 442 mm 455 mm

Net weight .......................................................................................... 5.8 kg 7.5 kg 7.5 kg

•

Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

•

Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can be operated on single-phase AC/DC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

Safety instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear pro-

tectors and thickly padded gloves.

2. Be sure the bit is secured in place before

operation.

3. Under normal operation, the tool is designed

to produce vibration. The screws can come

loose easily, causing a breakdown or accident.

Check tightness of screws carefully before

operation.

4. In cold weather or when the tool has not been

used for a long time, let the tool warm up for

several minutes by operating it under no load.

This will loosen up the lubrication. Without

proper warm-up, hammering operation is dif-

ficult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

6. Hold the tool firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not point the tool at any one in the area

when operating. The bit could fly out and

injure someone seriously.

10. When drilling or chipping into walls, floors or

wherever “live” electrical wires may be

encountered, DO NOT TOUCH ANY METAL

PARTS OF THE TOOL!

Hold the tool by the insulated grasping sur-

faces to prevent electric shock if you drill or

chip into a “live” wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Side grip (auxiliary handle) (Fig.1&2)

For maximum control and safer operation, always use

the side grip with this tool. The side grip swings

around to either side, allowing easy handling of the

tool in any position. Loosen the side grip by turning it

counterclockwise, swing it to the desired position and

then tighten it by turning clockwise. (Fig. 1)

The side grip can also be installed in the position

shown in Fig. 2. Remove the side grip from the grip

base by turning the side grip counterclockwise. Screw

the side grip on either side of the tool, whichever is

convenient.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR 3850K Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info