Bedienungsanleitung Makita hr 4011 c (Seite 7 von 23) (Englisch, Holländisch)

388901

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

ENGLISH

Explanation of general view

1 Switch trigger

2 Switch lever

3 Adjusting dial

4 Change lever

5 Pointer

6 Lock button

7 Power-ON indicator lamp

(green)

8 Service indicator lamp (red)

9 Side handle

10 Clamp nut

11 Side grip

12 Bit shank

13 Bit grease

14 Bit

15 Chuck cover

16 Depth gauge

17 Clamp screw

18 Blow-out bulb

19 Screws

20 Connector

21 Black

22 White

23 Screw

24 Crank cap cover

25 Control plate

26 Screwdriver

27 Crank cap

28 Hammer grease

SPECIFICATIONS

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intendended use

The tool is intended for hammer drilling in brick, concrete

and stone as well as for chiselling work.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

ENB010-2

1. Wear ear protectors. Exposure to noise can cause

hearing loss.

2. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

3. Hold tools by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring or its own cord. Con-

tact with a “live” wire will make exposed metal parts

of the tool “live” and shock the operator.

4. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask and thickly

padded gloves.

5. Be sure the bit is secured in place before opera-

tion.

6. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

7. In cold weather or when the tool has not been

used for a long time, let the tool warm up for a

while by operating it under no load. This will

loosen up the lubrication. Without proper warm-

up, hammering operation is difficult.

8. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

9. Hold the tool firmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

13. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

Model HR4001C HR4010C HR4011C

Capacities

Carbide-tipped bit 40 mm

Core bit 105 mm

No load speed (min

–1

) 235 – 480

Blows per minute 1,350 – 2,750

Overall length 468 mm

Net weight 5.9 kg 6.3 kg 6.3 kg

Safety class /II

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita hr 4011 c Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita hr 4011 c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info