Bedienungsanleitung Makita HR 5000 (Seite 5 von 10) (Englisch, Holländisch)

448545

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

ENGLISH

Explanation of general view

1 Clamp nut

2 Side handle

3 Side grip

4 Tool holder

5 Tool retainer

6 Change lever

7 For rotation with hammering

8 For hammering only

9 Switch trigger

10 Core bit

11 Adapter

12 Center bit

13 Rod

14 Hex wrench

15 Rear cover

16 Screwdriver

17 Brush holder cap

18 Lock nut wrench

19 Crank cap

20 Hammer grease

SPECIFICATIONS

Model HR5000 HR5000K

Capacities

Tungsten-carbide bit ........................................................................................ 50 mm 50 mm

Core bit

Concrete ........................................................................................................ 150 mm 150 mm

Hume pipe ..................................................................................................... 255 mm 255 mm

No load speed (min

–1

) ........................................................................................ 260 260

Blows per minute ................................................................................................ 2,100 2,100

Overall length ...................................................................................................... 476 mm 503 mm

Net weight ........................................................................................................... 9.6 kg 9.7 kg

•

Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

•

Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can be operated on single-phase AC/DC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

Safety instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear pro-

tectors and thickly padded gloves.

2. Be sure the bit is secured in place before

operation.

3. Under normal operation, the tool is designed

to produce vibration. The screws can come

loose easily, causing a breakdown or accident.

Check tightness of screws carefully before

operation.

4. In cold weather or when the tool has not been

used for a long time, let the tool warm up for

several minutes by operating it under no load.

This will loosen up the lubrication. Without

proper warm-up, hammering operation is dif-

ficult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

6. Hold the tool firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not point the tool at any one in the area

when operating. The bit could fly out and

injure someone seriously.

10. When drilling or chipping into walls, floors or

wherever “live” electrical wires may be

encountered, DO NOT TOUCH ANY METAL

PARTS OF THE TOOL!

Hold the tool by the insulated grasping sur-

faces to prevent electric shock if you drill or

chip into a “live” wire.

11. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Side handle (Fig. 1)

The side handle swings around 360° on the vertical

as well as back and forth on the horizontal. Turn the

clamp nut clockwise to secure the handle in the

desired position.

Side grip (Fig. 2)

The side grip is convenient for downward drilling or

chipping operations. Screw the side grip on the tool

securely. The side grip can be installed on either side

of the tool for right or left hand operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR 5000 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info