Bedienungsanleitung Makita HR1820 (Seite 6 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

599634

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Adjusting depth of drilling (Fig. 2)

Loosen the wing bolt and adjust the depth gauge to

the desired depth. After adjusting, tighten the wing

bolt.

Side grip (auxiliary handle) (Fig. 3)

The side grip swings around to either side, allowing

easy handling of the tool in any position. Loosen

the side grip by turning it counterclockwise, swing it to

the desired position and then tighten it by turning

clockwise.

Selecting action mode

For HR1820 (Fig.4&5)

Rotation with hammering:

For drilling in concrete, granite, tile, etc., press the

push rod in the

direction. (Fig. 4)

Rotation only:

For drilling in wood or metal, press the push rod in the

direction. (Fig. 5)

CAUTION:

To avoid rapid wear on the mode change mechanism,

be sure to press the push rod as far as it will go.

For HR2510 (Fig.6&7)

Rotation with hammering:

For drilling in concrete, granite, tile, etc., rotate the

change lever to the

position. (Fig. 6)

Rotation only:

For drilling in wood or metal, rotate the change lever

to the

position. (Fig. 7)

CAUTION:

To avoid rapid wear on the mode change mechanism,

be sure that the change lever is always positively

located in one of the two action mode positions.

Switch action (Fig. 8)

CAUTION:

•

Before plugging in the tool, always check to

see that the switch trigger actuates properly and

returns to the ‘‘OFF’’ position when released.

•

Do not tape, tie or otherwise secure the trigger in

the ‘‘ON’’ position.

To start the tool simply pull the trigger. Tool

speed is increased by increasing pressure on the

trigger. Release the trigger to stop. A speed control

screw is provided so that maximum tool speed

can be limited (variable). Turn the speed control

screw clockwise for higher speed, and counterclock-

wise for lower speed.

Hammer drilling operation

Position the bit at the location for the hole, then pull

the trigger.

Do not force the tool. Light pressure gives best

results. Keep the tool in position and prevent it

from slipping away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the

tool at an idle, then remove from the hole. By

repeating this several times, the hole will be cleaned

out.

CAUTION:

When the bit begins to break through concrete or if

the bit strikes reinforcing rods embedded in concrete,

the tool may react dangerously. Maintain good

balance and safe footing while holding the tool

firmly with both hands to prevent dangerous reaction.

Dust collector (Fig. 9)

Use the dust collector for safe, sanitary overhead

operations. Install the bit, then attach the dust collec-

tor on the end by turning and applying pressure. Then

secure it by turning the metal retainer clockwise.

CAUTION:

Empty the dust collector of its contents after drilling

every 2 or 3 holes.

Drilling in wood or metal (Fig. 10)

For HR1820

Set the push rod for ‘‘rotation only’’. Use the optional

drill chuck and chuck adapter for drilling up to 10 mm

in metal and up to 15 mm in wood. To install the drill

chuck and chuck adapter, refer to ‘‘Installing or

removing drill bit’’.

For HR2510

Set the change lever for ‘‘rotation only’’. Use the

optional drill chuck and chuck adapter for drilling up to

13 mm in metal and up to 30 mm in wood. To install

the drill chuck and chuck adapter, refer to ‘‘Installing

or removing drill bit’’.

CAUTION:

When the drill chuck is installed on this tool, do

not use ‘‘rotation with hammering’’ action. The drill

chuck and chuck adapter may be damaged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR1820 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info