Bedienungsanleitung Makita HR1841F (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691028

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

7 ENGLISH

Selecting the action mode

NOTICE: Do not rotate the action mode chang-

ing knob when the tool is running.Thetoolwillbe

damaged.

NOTICE: To avoid rapid wear on the mode

change mechanism, be sure that the action mode

changing knob is always positively located in one

of the action mode positions.

Rotation with hammering

For drilling in concrete, masonry, etc., rotate the action

mode changing knob to the symbol. Use a car-

bide-tipped drill bit.

►Fig.4: 1.Actionmodechangingknob

Rotation only

For drilling in wood, metal or plastic materials, rotate

the action mode changing knob to the symbol. Use a

twist drill bit or wood drill bit.

►Fig.5: 1.Actionmodechangingknob

Torque limiter

NOTICE: As soon as the torque limiter actuates,

switch off the tool immediately.Thiswillhelppre-

vent premature wear of the tool.

NOTICE: Drill bits such as hole saw, which tend

to pinch or catch easily in the hole, are not appro-

priate for this tool.Thisisbecausetheywillcause

the torque limiter to actuate too frequently.

Thetorquelimiterwillactuatewhenacertaintorque

levelisreached.Themotorwilldisengagefromthe

output shaft. When this happens, the drill bit will stop

turning.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Side grip (auxiliary handle)

CAUTION: Always use the side grip to ensure

safe operation.

CAUTION: After installing or adjusting the

side grip, make sure that the side grip is rmly

secured.

Installthesidegripsothatthegroovesonthegriptin

theprotrusionsonthetoolbarrel.Turnthegripclock-

wisetosecureit.Thegripcanbexedatdesiredangle.

►Fig.6: 1. Side grip

Grease

Coat the shank end of the drill bit beforehand with a

small amount of grease (about 0.5 - 1 g).

Thischucklubricationassuressmoothactionandlon-

ger service life.

Installing or removing drill bit

Clean the shank end of the drill bit and apply grease

before installing the drill bit.

►Fig.7: 1. Shank end 2. Grease

Insertthedrillbitintothetool.Turnthedrillbitandpush

it in until it engages.

Afterinstallingthedrillbit,alwaysmakesurethatthe

drill bit is securely held in place by trying to pull it out.

►Fig.8: 1. Drill bit

Toremovethedrillbit,pullthechuckcoverdownallthe

way and pull the drill bit out.

►Fig.9: 1. Drill bit 2. Chuck cover

Depth gauge

Thedepthgaugeisconvenientfordrillingholesofuniform

depth. Loosen the side grip and insert the depth gauge

intotheholeonthesidegrip.Adjustthedepthgaugeto

thedesireddepthandtightenthesidegriprmly.

►Fig.10: 1. Hole 2. Depth gauge

NOTE: Make sure that the depth gauge does not

touch the main body of the tool when attaching it.

Dust cup (optional accessory)

Use the dust cup to prevent dust from falling over the tool and

on yourself when performing overhead drilling operations.

Attachthedustcuptothebitasshowninthegure.Thesize

of bits which the dust cup can be attached to is as follows.

Model Bit diameter

Dust cup 5 6 mm - 14.5 mm

Dust cup 9 12 mm - 16 mm

►Fig.11: 1. Dust cup

Dust cup set (optional accessory)

NOTICE: Do not use the dust cup set when drill-

ing in metal or similar. It may damage the dust cup

set due to the heat produced by small metal dust or

similar. Do not install or remove the dust cup set with

the drill bit installed in the tool. It may damage the

dust cup set and cause dust leak.

NOTE: The standard side grip cannot be used

with the dust cup set being installed on the tool.

When the dust cup set is installed on the tool, remove

the grip from the standard side grip, and then attach it

to the optional grip base set.

Before installing the dust cup set, remove the bit from

the tool if installed.

Installthespacersothatthegroovesonthespacertin

the protrusions on the tool barrel while widening it. Be

careful for the spring not to come off from the slit of spacer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR1841F Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info