Bedienungsanleitung Makita HR2611F (Seite 9 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

599645

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Hammering only (Fig. 9)

For chipping, scaling or demolition operations, rotate the

action mode changing knob to the

g symbol. Use a bull

point, cold chisel, scaling chisel, etc.

CAUTION:

• Do not rotate the action mode changing knob when the

tool is running under load. The tool will be damaged.

• To avoid rapid wear on the mode change mechanism,

be sure that the action mode changing knob is always

positively located in one of the three action mode posi-

tions.

• When changing from the

g symbol mode to the m sym-

bol mode, the action mode changing knob may no

longer move in the

symbol position. At this time,

turn the tool on or turn the chuck by hand in the

symbol position and then rotate the action mode

changing knob. Forcing the action mode changing knob

may cause tool damage.

Torque limiter

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

CAUTION:

• As soon as the torque limiter actuates, switch off the

tool immediately. This will help prevent premature wear

of the tool.

• Bits such as hole saw, which tend to pinch or catch

easily in the hole, are not appropriate for this tool. This

is because they will cause the torque limiter to actuate

too frequently.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Side grip (auxiliary handle) (Fig. 10)

CAUTION:

• Always use the side grip to ensure operating safety.

Install the side grip so that the protrusions on the grip fit

in between the grooves on the tool barrel. Then tighten

the grip by turning clockwise at the desired position. It

may be swung 360° so as to be secured at any position.

Bit grease

Coat the bit shank head beforehand with a small amount

of bit grease (about 0.5–1g).

This chuck lubrication assures smooth action and longer

service life.

Installing or removing the bit

Clean the bit shank and apply bit grease before installing

the bit. (Fig. 11)

Insert the bit into the tool. Turn the bit and push it in until

it engages. (Fig. 12)

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the way

and pull the bit out. (Fig. 13)

Bit angle (when chipping, scaling or demolishing)

For Models HR2310T, HR2610, HR2610T, HR2611F,

HR2611FT

The bit can be secured at the desired angle. To change

the bit angle, rotate the action mode changing knob to

the O symbol. Turn the bit to the desired angle. (Fig. 14)

Rotate the action mode changing knob to the

g symbol.

(Fig. 15)

Then make sure that the bit is securely held in place by

turning it slightly.

Depth gauge

The depth gauge is convenient for drilling holes of uni-

form depth. (Fig. 16)

Press the lock button on the grip base in the direction of

arrow shown in the figure and with the lock button being

pressed insert the depth gauge into the hex. hole in the

grip base. (Fig. 17)

At this time, the depth gauge needs to be inserted so that

its toothed side is directed to the toothed side of hex hole

marking on the grip base as shown in Fig. 18.

Adjust the depth gauge to the desired depth by moving it

back and forth while pressing the lock button. After the

adjustment, release the lock button to lock the depth

gauge. (Fig. 19)

NOTE:

• Inserting the depth gauge with its toothed side not

directed to the toothed side of hex hole marking on the

grip base as shown in the figure does not allow the

depth gauge to be locked.

Dust cup (Fig. 20)

Use the dust cup to prevent dust from falling over the tool

and on yourself when performing overhead drilling

operations. Attach the dust cup to the bit as shown in

Fig. 20. The size of bits which the dust cup can be

attached to is as follows.

006406

There is another type of dust cup (accessory) which

helps you prevent dust from falling over the tool and on

yourself when performing overhead drilling operations.

Installing or removing the dust cup

Before installing the dust cup, remove the bit from the

tool if installed on the tool. Install the dust cup (acces-

sory) on the tool so that the symbol on the dust cup is

aligned with the grooves in the tool. (Fig. 21)

To remove the dust cup, pull the chuck cover in the direc-

tion as shown in Fig. 22 and with the chuck cover pulled

take the bit out of the tool.

And then grab the attachment at the foot of dust cup and

take it out. (Fig. 23)

NOTE:

• When installing or removing the dust cup, the cap may

come off the dust cup. At that time, proceed as follows.

Remove the bellows from the attachment and fit the

cap from the side shown in the figure with its carved

side facing upward so that the groove in the cap fits in

the inside periphery of the attachment. Finally, mount

the bellows that has been removed. (Fig. 24, 25 & 26)

Bit diameter

Dust cup 5 6 mm – 14.5 mm

Dust cup 9 12 mm – 16 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR2611F Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info