Bedienungsanleitung Makita HR2630T (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599668

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

4. Wear a hard hat (safety helmet), safety glasses

and/or face shield. Ordinary eye or sun glasses

are NOT safety glasses. It is also highly

recommended that you wear a dust mask and

thickly padded gloves.

5. Be sure the bit is secured in place before

operation.

6. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

7. In cold weather or when the tool has not been

used for a long time, let the tool warm up for a

while by operating it under no load. This will

loosen up the lubrication. Without proper warm-

up, hammering operation is difficult.

8. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

9. Hold the tool firmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area when

operating. The bit could fly out and injure

someone seriously.

13. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

14. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1 & 2)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop. For continuous

operation, pull the switch trigger, push in the lock button

and then release the switch trigger. To stop the tool from

the locked position, pull the switch trigger fully, then

release it.

Lighting up the lamps (Fig. 3)

For Model HR2631F, HR2631FT

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the lamp, pull the trigger. Release the trigger

to turn it off.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

• Do not use thinner or gasoline to clean the lamp. Such

solvents may damage it.

Reversing switch action (Fig. 4 & 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

For Model HR2631F, HR2631FT, HR2320T, HR2630,

HR2630T

CAUTION:

• If the switch trigger can not be depressed, check to see

that the reversing switch is fully set to position (A

side) or (B side).

This tool has a reversing switch to change the direction

of rotation. Move the reversing switch lever to the

position (A side) for clockwise rotation or to the

position (B side) for counterclockwise rotation.

For Model HR2641

NOTE:

• When you operate the tool in counterclockwise

rotation, the switch trigger is pulled only halfway and

the tool runs at half speed. For counterclockwise

rotation, you cannot push in the lock button.

This tool has a reversing switch to change the direction

of rotation. Move the reversing switch lever to the

position (A side) for clockwise rotation or the

position (B side) for counterclockwise rotation.

Changing the quick change chuck for SDS-plus

For Model HR2631FT, HR2320T, HR2630T

The quick change chuck for SDS-plus can be easily

exchanged for the quick change drill chuck.

Removing the quick change chuck for SDS-plus

(Fig. 6)

CAUTION:

• Before removing the quick change chuck for SDS-plus,

always remove the bit.

Grasp the change cover of the quick change chuck for

SDS-plus and turn in the direction of the arrow until the

change cover line moves from the symbol to the

symbol. Pull forcefully in the direction of the arrow.

Attaching the quick change drill chuck (Fig. 7)

Check the line of the quick change drill chuck shows the

symbol. Grasp the change cover of the quick change

drill chuck and set the line to the symbol.

Place the quick change drill chuck on the spindle of the

tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR2630T Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info