Bedienungsanleitung Makita HR2661 (Seite 11 von 16) (Englisch)

691065

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

11 ENGLISH

Drilling in wood or metal

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece. There is a tremendous force exerted on

the tool/drill bit at the time of hole break through.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

NOTICE: Never use “rotation with hammering”

when the drill chuck is installed on the tool. The

drill chuck may be damaged.

Also, the drill chuck will come off when reversing the

tool.

NOTICE: Pressing excessively on the tool will

not speed up the drilling. In fact, this excessive

pressure will only serve to damage the tip of your drill

bit, decrease the tool performance and shorten the

service life of the tool.

Set the action mode changing knob to the symbol.

For HR2650/HR2651/HR2661

Optional accessory

Attach the chuck adapter to a keyless drill chuck to

which 1/2"-20 size screw can be installed, and then

install them to the tool. When installing it, refer to the

section “Installing or removing drill bit”.

1 2

►1. Keyless drill chuck 2. Chuck adapter

For HR2651T

Use the quick change drill chuck as standard equip-

ment. When installing it, refer to "changing the quick

change chuck for SDS-plus".

Hold the ring and turn the sleeve counterclockwise to

openthechuckjaws.Placethebitinthechuckasfaras

itwillgo.Holdtheringrmlyandturnthesleeveclock-

wise to tighten the chuck.

►1. Sleeve 2. Ring

To remove the bit, hold the ring and turn the sleeve

counterclockwise.

Diamond core drilling

NOTICE: If performing diamond core drilling

operations using “rotation with hammering”

action, the diamond core bit may be damaged.

When performing diamond core drilling operations,

always set the change lever to the position to use

"rotation only" action.

Disposing of dust

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

CAUTION: Be sure to wear dust mask when

disposing of dust.

CAUTION: Empty the dust case regularly

before the dust case becomes full. Failure to do so

may decrease the dust collection performance and

cause dust inhalation.

CAUTION: The performance of dust collection

decreases if the lter in the dust case become

clogged. Replace the lter with new one after

approximately 200 times of dust fulllment as a

guide. Failure to do so may cause dust inhalation.

1. Remove the dust case while pressing down the

lever of the dust case.

►1. Lever

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR2661 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HR2661

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info