793651
22
Zoom out
Zoom in
Vorherige Seite
1/156
Nächste Seite
22 ENGLISH
MAINTENANCE
CAUTION:
Always be sure that the tool is switched
󰀨-
ing to perform inspection or maintenance.
CAUTION:
Clean out the upper and lower guards
to ensure there is no accumulated sawdust which may
impede the operation of the lower guarding system. A

󰀨
If
the dust is being blown out of the guards, be sure the
proper eye and breathing protection is used.
CAUTION: 󰀨
dust on the tool.

NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,



Adjusting 0°-cut or 45°-cut accuracy
NOTICE: Do not engage the levers for -1° bevel
angle when adjusting 0°-cut accuracy.
NOTICE:
Do not engage the positive stopper for 22.5°
or 60° bevel angle when adjusting 45°-cut accuracy.

󰀨
1. Loosen the clamping screws on the front and rear
of the tool so that the bevel angle can be changed. Set


Fig.46: 1. Clamping screw 2. Positive stopper
2.
Make the base perpendicular or 45° to the circular saw


Fig.47: 1. Triangular rule
Fig.48: 1.2.
screw for 45° angle
3. Tighten the clamping screws and then make a test
cut to check if desired angle is obtained.
Adjusting the depth guide


depth guide as follows:
1. Make the base perpendicular, and set the depth of
cut to the deepest.
 

 
 
for parallelism.
Fig.49: 1.
Adjusting the parallelism
CAUTION: Keep the parallelism accurate.




󰀨
1. Set the tool to the maximum cutting depth.
2. Make sure all levers and screws are tightened.
3. 
4. While opening the lower guard, move the rear of
the base so that the distance A and B becomes equal.
Fig.50: 1. Screw 2. Base
5. Tighten the screws and make a test cut to check
the parallelism.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool

accessories or attachments might present a risk of

for its stated purpose.
-

Center.
Circular saw blade
Sub base
Guide rail
Bevel guide
• Clamp
• Sheet
Rubber sheet
Position sheet
Hex wrench
 󰀨
Wireless unit
 
NOTE:

󰀨
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita HS011G wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info