Bedienungsanleitung Makita HS0600 (Seite 10 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691834

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

10 ENGLISH

Donotusethedustnozzlewiththelongleverattached.

Youwillnotbeabletomakeacutbecausethelower

guard movement is hindered by the dust nozzle.

2. Install the dust nozzle on the tool using the screw.

►Fig.19: 1.Dustnozzle2. Screw

3. Connect a hose of the vacuum cleaner to the dust

nozzle.

►Fig.20

OPERATION

CAUTION: Be sure to move the tool forward

in a straight line gently. Forcing or twisting the tool

will result in overheating the motor and dangerous

kickback,possiblycausingsevereinjury.

►Fig.21

Holdthetoolrmly.Thetoolisprovidedwithbothafront

grip and rear handle. Use both to best grasp the tool.

If both hands are holding saw, they cannot be cut by

the circular saw blade. Set the base on the workpiece

to be cut without the circular saw blade making any

contact.Thenturnthetoolonandwaituntilthecircular

saw blade attains full speed. Now simply move the tool

forwardovertheworkpiecesurface,keepingitatand

advancing smoothly until the sawing is completed.

Togetcleancuts,keepyoursawinglinestraightand

your speed of advance uniform. If the cut fails to prop-

erly follow your intended cut line, do not attempt to turn

orforcethetoolbacktothecutline.Doingsomaybind

the circular saw blade and lead to dangerous kickback

andpossibleseriousinjury.Releaseswitch,waitforcir-

cular saw blade to stop and then withdraw tool. Realign

toolonnewcutline,andstartcutagain.Attemptto

avoid positioning which exposes operator to chips and

wooddustbeingejectedfromsaw.Useeyeprotection

tohelpavoidinjury.

If the front grip become loose, turn it counterclockwise

to tighten.

►Fig.22: 1. Front grip

Rip fence (Guide rule)

Optional accessory

►Fig.23: 1.Ripfence(Guiderule)2. Clamping screw

Thehandyripfenceallowsyoutodoextra-accurate

straight cuts. Simply slide the rip fence up snugly

against the side of the workpiece and secure it in posi-

tion with the clamping screw on the front of the base. It

also makes repeated cuts of uniform width possible.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and unplugged before attempting to

perform inspection or maintenance.

CAUTION: Clean out the guard to ensure

there is no accumulated sawdust and chips

which may impede the operation of the guarding

system.Adirtyguardingsystemmaylimittheproper

operation which could result in serious personal

injury.Themosteffectivewaytoaccomplishthis

cleaning is with compressed air. If the dust is being

blown out of the guard, be sure the proper eye

and breathing protection is used.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

Adjusting the parallelism

Thisadjustmenthasbeenmadeatthefactory.Butifitis

off,youcanadjustitasthefollowingprocedure.

1. Make sure all levers and screws are tightened.

Slightly loosen the screw illustrated.

2. Whileopeningthelowerguard,movetherearof

thebasesothatthedistanceAandBbecomesequal.

3. Tightenthescrewsandmakeatestcuttocheck

the parallelism.

►Fig.24: 1. Screw

Adjusting 0°-cut accuracy

Thisadjustmenthasbeenmadeatthefactory.Butifitis

off,youcanadjustitasthefollowingprocedure.

1. Slightly loosen the lever and clamping screw on

the front and rear of the tool.

2. Make the base perpendicular to the blade using

atriangularruleorsquarerulebyturningtheadjusting

screw.

►Fig.25: 1.Triangularrule2.Adjustingscrew

3. Tightentheleverandclampingscrewandthen

make a test cut to check the verticalness.

Replacing carbon brushes

►Fig.26: 1. Limit mark

Check the carbon brushes regularly.

Replace them when they wear down to the limit mark.

Keep the carbon brushes clean and free to slip in the

holders. Both carbon brushes should be replaced at the

same time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps.

2. Takeouttheworncarbonbrushes,insertthenew

ones and secure the brush holder caps.

►Fig.27: 1. Brush holder cap

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers, always using Makita replacement parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HS0600 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info