Bedienungsanleitung Makita HS301DZJ (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711053

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

8 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoffyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

►Fig.7: 1. Red indicator 2. Button 3. Battery

cartridge

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

notbeinginsertedcorrectly.

Battery protection system

Thetoolisequippedwithabatteryprotectionsystem.

Thissystemautomaticallycutsoffpowertothemotorto

extendbatterylife.

Thetoolwillautomaticallystopduringoperationifthe

tooland/orbatteryareplacedunderoneofthefollowing

conditions:

Overloaded:

Thetoolisoperatedinamannerthatcausesittodraw

anabnormallyhighcurrent.

In this situation, release the switch trigger on the tool

andstoptheapplicationthatcausedthetooltobecome

overloaded.Thenpulltheswitchtriggeragaintorestart.

Ifthetooldoesnotstart,thebatteryisoverheated.

Inthissituation,letthebatterycoolbeforepullingthe

switch trigger again.

Low battery voltage:

Theremainingbatterycapacityistoolowandthetool

will not operate. If you pull the switch trigger, the motor

runsagainbutstopssoon.Inthissituation,removeand

rechargethebattery.

Indicating the remaining battery

capacity

Only for battery cartridges with "B" at the end of the

model number

►Fig.8: 1.Indicatorlamps 2.Checkbutton

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for few seconds.

Indicator lamps Remaining

capacity

Lighted Off

75% to 100%

50% to 75%

25% to 50%

0% to 25%

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydifferslightly

from the actual capacity.

Adjusting depth of cut

►Fig.9: 1. Clamping screw 2. Depth guide

CAUTION: After adjusting the depth of cut,

always tighten the clamping screw securely.

Loosen the clamping screw on the depth guide and

movethebaseupordown.Atthedesireddepthofcut,

securethebasebytighteningtheclampingscrew.

For cleaner, safer cuts, set cut depth so that no more

thanonebladetoothprojectsbelowworkpiece.Using

proper cut depth helps to reduce potential for danger-

ousKICKBACKSwhichcancausepersonalinjury.

Bevel cutting

►Fig.10: 1. Clamping screw 2. Bevel scale plate

Loosentheclampingscrewonthebevelscaleplateon

thefrontofthebase.Setforthedesiredangle(0°-45°)

bytiltingaccordingly,thentightentheclampingscrew

securely.

Sighting

►Fig.11: 1. Cutting line

Forstraightcuts,aligntheApositiononthefrontofthe

basewithyourcuttingline.For45°bevelcuts,alignthe

B position with it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HS301DZJ Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info