Bedienungsanleitung Makita HS6101 (Seite 5 von 18) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691837

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

ENGLISH (Original instructions)

Explanation of general view

1 Lever

2 Front lever

3 Rear wing nut

4 Stopper

5 0° position

6 45° position

7 Cutting line

8Screw

9 Switch trigger

10 Lock-off button

11 Light

12 Hex wrench

13 Loosen

14 Tighten

15 Shaft lock

16 Mounting shaft

17 Inner flange

18 Saw blade

19 Outer flange

20 Hex bolt

21 Ring

22 Dust nozzle

23 Vacuum cleaner

24 Hose

25 Clamp lever

26 Rip fence (Guide rule)

27 Adjusting screw for 0°

28 Adjusting screw for 45°

29 Triangular rule

30 Base

31 Limit mark

32 Screwdriver

33 Brush holder cap

SPECIFICATIONS

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE078-1

Intended use

The tool is intended for performing lengthways and

crossways straight cuts and mitre cuts with angles in

wood while in firm contact with the workpiece. With

appropriate saw blades, aluminum can also be sawed.

ENF100-1

For public low-voltage distribution systems of

between 220 V and 250 V

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.32 Ohms it can be presumed that

there will be no negative effects.

The mains socket used for this device must be protected

with a fuse or protective circuit breaker having slow trip-

ping characteristics.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and instruc-

tions may result in electric shock, fire and/or serious

injury.

Save all warnings and instructions for future reference.

GEB013-6

CIRCULAR SAW SAFETY WARNINGS

Cutting procedures

1. DANGER: Keep hands away from cutting

area and the blade. Keep your second hand on

auxiliary handle, or motor housing. If both hands

are holding the saw, they cannot be cut by the blade.

2. Do not reach underneath the workpiece. The

guard cannot protect you from the blade below the

workpiece.

3. Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

4. Never hold piece being cut in your hands or

across your leg. Secure the workpiece to a

stable platform. It is important to support the work

properly to minimize body exposure, blade binding,

or loss of control.

000157

Model HS6100 HS6101 HS7100 HS7101

Blade diameter 165 mm 190 mm

Max. cutting depth

at 0° 54.5 mm 67 mm

at 45° 39.5 mm 48.5 mm

at 50° 35.5 mm 43.5 mm

No load speed (min

–1

) 5,500

Overall length 297 mm 310 mm

Net weight 3.7 kg 3.7 kg 4.0 kg 4.0 kg

Safety class /II

A typical illustration of proper hand support,

workpiece support, and supply cord routing (if

applicable).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HS6101 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info