Bedienungsanleitung Makita JN 3200 (Seite 4 von 12) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448555

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

Explanation of general view

1 Lock button

2 Switch trigger

3 Gauge for mild steel : 3.2 mm

4 Gauge for stainless : 2.5 mm

5 Mouth (3.5 mm clearance)

6 Wrench

7 Lock nut

8 Die holder

9 Punch

10 Screw

11 Loosen

12 Cutting edge

13 Groove

14 Pin

15 Punch holder

16 Grind/sharpen; 0.3 – 0.4 mm

17 Remove dull portion

18 Die

19 Washer

20 Limit mark

21 Screwdriver

22 Brush holder cap

SPECIFICATIONS

Model JN3200

Max. cutting capacities

Steel up to 400 N/mm

........................... 3.2 mm/10 ga

Steel up to 600 N/mm

........................... 2.5 mm/13 ga

Steel up to 800 N/mm

........................... 1.0 mm/20 ga

Aluminum up to 200 N/mm

................... 2.5 mm/13 ga

Min. cutting radius

Outside edge ................................................... 128 mm

Inside edge ...................................................... 120 mm

Strokes per minute ................................................. 1,300

Overall length ..................................................... 215 mm

Net weight ............................................................. 3.4 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed Safety

instructions.

ADDITIONAL SAFETY RULES

1. Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

2. Always lead the power supply cord away from

the tool towards the rear.

3. Do not touch the blade or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Pre-lubrication

Coat the cutting line with tool oil when cutting mild steel

or stainless; use light oil or kerosene when cutting alumi-

num.

Switch action (Fig. 1)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

Permissible cutting thickness (Fig. 2)

The thickness of material to be cut depends upon the

tensile strength of the material itself. The groove on the

die holder acts as a thickness gauge. Do not attempt to

cut any material which will not fit into this groove.

This tool can cut any thickness of aluminum plate that fits

into the tool’s mouth (3.5 mm clearance).

Cutting method (Fig. 3)

Smooth cutting is achieved by holding the tool upright

and applying gentle pressure in the cutting direction.

Apply tool oil to the punch about every 10 meters of mild

steel or stainless steel to be cut. Light oil or kerosene

should be used to keep an aluminum lubricated continu-

ously. Failure to lubricate aluminum in the cut will cause

chips to adhere to the tool, dulling the die and punch and

increasing load on the motor.

Cutouts (Fig. 4)

Cutouts can be done by first opening a round hole of

about 42 mm diameter or more in the material.

Max.cutting capacities mm ga

Steel up to 400 N/mm

3.2 10

Steel up to 600 N/mm

2.5 13

Steel up to 800 N/mm

1.0 20

Aluminum up to 200 N/mm

2.5 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JN 3200 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info