Bedienungsanleitung Makita JN3201 (Seite 5 von 36) (Deutsch, Englisch, Polnisch)

599024

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function

on the tool.

Permissible cutting thickness

Fig.1

The thickness of material to be cut depends upon the

tensile strength of the material itself. The groove on the

die holder acts as a thickness gauge for allowable

cutting thickness. Do not attempt to cut any material

which will not fit into this groove.

Max.cutting capacities mm ga

Steel up to 400 N/mm

3.2 10

Steel up to 600 N/mm

2.5 13

Steel up to 800 N/mm

1.0 20

Aluminum up to 200 N/mm

3.5 10

006439

Switch action

Fig.2

CAUTION:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and

returns to the "OFF" position when released.

• Switch can be locked in "ON" position for ease of

operator comfort during extended use. Apply

caution when locking tool in "ON" position and

maintain firm grasp on tool.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

For continuous operation, pull the switch trigger and

then push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

Punch replacement

Fig.3

Fit the wrench provided onto the lock nut and tap the

handle lightly with a hammer to loosen the lock nut.

Take off the die holder and use a wrench to remove the

screw. Then remove the punch.

Fig.4

To install the punch, insert it into the punch holder with

its cutting edge facing forward so that the pin in the

punch holder fits into the groove in the punch. Install the

screw and lock nut. Then tighten them securely.

NOTE:

• When installing the screw and lock nut, be sure to

tighten securely. If they become loose during

operation, the tool may break down.

Fig.5

OPERATION

CAUTION:

• Hold the tool firmly with one hand on the main

handle when performing the tool.

Pre-lubrication

Coat the cutting line with machine oil to increase the

punch and die service life. This is particularly important

when cutting aluminum.

Cutting method

Fig.6

Smooth cutting is achieved by holding the tool upright

and applying gentle pressure in the cutting direction.

Apply tool oil to the punch about every 10 meters of mild

steel or stainless steel to be cut. Light oil or kerosene

should be used to keep an aluminum lubricated

continuously. Failure to lubricate aluminum in the cut will

cause chips to adhere to the tool, dulling the die and

punch and increasing load on the motor.

Cutouts

Fig.7

Cutouts can be done by first opening a round hole of

about 42 mm diameter or more in the material.

Cutting stainless steel

Fig.8

There is more vibration when cutting stainless steel than

mild steel. Less vibration and better cutting is possible

by adding another washer (standard equipment)

beneath the die.

Use the hex wrench provided to remove the two screws

and insert the washer below the die. Replace screws

and tighten securely.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

•

Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean.

Regularly clean the tool's air vents or whenever the

vents start to become obstructed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JN3201 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info