Bedienungsanleitung Makita jr 3000 vt (Seite 4 von 12) (Englisch, Holländisch)

383006

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

Explanation of general view

1 Released position

2 Fixed position

3 Blade clamp sleeve

4Blade

5Lever

6 Shoe

7 Switch trigger

8 Lock button/Lock-off button

9 Speed control screw

10 High

11 Low

SPECIFICATIONS

Model JR3000VT

Length of stroke .................................................... 30 mm

Strokes per minute ........................................... 0 – 2,300

Cutting capacities

Pipe ................................................................... 90 mm

Wood ................................................................. 90 mm

Overall length ..................................................... 438 mm

Net weight ............................................................. 3.1 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for sawing wood, plastic, metal and

building materials with a strong impact. It is suitable for

straight and curved cutting.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES FOR TOOL

ENB012-1

1. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tools

may contact hidden wiring or its own cord. Con-

tact with a “live” wire will make exposed metal

parts of the tool “live” and shock the opeator.

2. Avoid cutting nails. Inspect workpiece for any

nails and remove them before operation.

3. Do not cut oversize workpiece.

4. Check for the proper clearance beyond the work-

piece before cutting so that the blade will not

strike the floor, workbench, etc.

5. Hold the tool firmly.

6. Make sure the blade is not contacting the work-

piece before the switch is turned on.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Always switch off and wait for the blade to come

to a complete stop before removing the blade

from the workpiece.

10. Do not touch the blade or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing saw blade

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

• Always clean out all chips or foreign matter adhering to

the blade, blade clamp and/or slider. Failure to do so

may cause insufficient tightening of the blade, resulting

in a serious injury.

To install the saw blade, always make sure that the blade

clamp sleeve is in released position before inserting the

saw blade. If the blade clamp sleeve is in fixed position,

rotate the sleeve to the released position. (Fig. 3)

Insert the saw blade into the blade clamp as far as it will

go. The blade clamp sleeve rotates and the saw blade is

fixed. Make sure that the saw blade cannot be extracted

even though you try to pull it out. (Fig. 4)

NOTE:

If you do not insert the saw blade deep enough, the saw

blade may be ejected unexpectedly during operation.

This can be extremely dangerous.

To remove the saw blade, rotate the blade clamp sleeve

in the direction of the arrow fully. The saw blade is

removed and the blade clamp sleeve is fixed at the

released position. (Fig. 5)

NOTE:

If you remove the saw blade without rotating the blade

clamp sleeve fully, the sleeve may not be fixed. In this

case, rotate the blade clamp sleeve fully to make the

sleeve fixed at the released position.

Adjusting the shoe (Fig. 6)

When the blade loses its cutting efficiency in one place

along its cutting edge, reposition the shoe to utilize a

sharp, unused portion of its cutting edge. This will help to

lengthen the life of the blade. To reposition the shoe,

loosen the lever and slide the shoe forward or back to the

desired position. Then tighten the lever to firmly secure

the shoe.

Switch action (Fig. 7)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

For tools with lock button

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop. For continuous operation, pull the trig-

ger and then push in the lock button. To stop the tool from

the locked position, pull the trigger fully, then release it. A

speed control screw is provided so that maximum tool

speed can be limited (variable). Turn the speed control

screw clockwise for higher speed, and counterclockwise

for lower speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita jr 3000 vt Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita jr 3000 vt

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info