Bedienungsanleitung Makita jr3020 (Seite 6 von 40) (Deutsch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

382507

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Switch action (Fig. 7, 8 & 9)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

For tools with lock button

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

Tool speed can be adjusted by turning the speed change

knob. When the portion with

v mark is positioned

adjacent to the pointer, faster speed can be obtained by

turning the knob clockwise.

When the portion with

w mark is positioned adjacent

to the pointer, full speed can be obtained.

Continuous operation can be performed only when the

knob is set to the full speed position. To perform continu-

ous operation, pull the trigger fully and then push the lock

button up. To stop the tool from the locked position, pull

the trigger fully, then release it.

For tools with lock-off button

To prevent the trigger from being accidentally pulled, a

lock-off button is provided. To start the tool, push the

lock-off button up and pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

Tool speed can be adjusted by turning the speed change

knob. When the portion with

v mark is positioned

adjacent to the pointer, faster speed can be obtained by

turning the knob clockwise.

When the portion with

w mark is positioned adjacent

to the pointer, full speed can be obtained.

Operation (Fig. 10)

Press the shoe firmly against the workpiece. Do not allow

the tool to bounce. Bring the blade into light contact with

the workpiece. First, make a pilot groove, using a slower

speed. Then use a faster speed to continue cutting.

CAUTION:

• Always use a suitable coolant (cutting oil) when cut-

ting metal. Failure to do so will cause premature

blade wear.

• Always wear gloves to protect your hands from hot

flying chips when cutting metal.

• Always press the shoe firmly against the workpiece

during operation. If the shoe is held away from the

workpiece during operation, strong vibration and/or

twisting will be produced, causing the blade to snap

dangerously.

• Be sure to always wear suitable eye protection

which conforms with current national standards.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 11 & 12)

Replace carbon brushes when they are worn down to the

limit mark. Both identical carbon brushes should be

replaced at the same time.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Centre.

Position Cutting action Applications

Straight line cutting action For cutting mild steel, stainless steel and plastics.

For clean cuts in wood and plywood.

Small orbit cutting action For cutting mild steel, aluminum and hard wood.

Medium orbit cutting action For cutting wood and plywood.

For fast cutting in aluminum and mild steel.

III

Large orbit cutting action For fast cutting in wood and plywood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita jr3020 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita jr3020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info