Bedienungsanleitung Makita jr3050 t (Seite 5 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

382562

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

For continuous operation, pull the switch trigger and then

push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing saw blade

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade, blade clamp and/or slider. Failure to do so

may cause insufficient tightening of the blade, resulting

in a serious injury.

To install the saw blade, always make sure that the blade

clamp lever is in released position on the insulation

cover before inserting the saw blade. If the blade clamp

lever is in fixed position, rotate the blade clamp lever in

the direction of the arrow so that it can be locked at the

released position . (Fig. 4)

Insert the saw blade into the blade clamp as far as it will

go. The blade clamp lever rotates and the saw blade is

fixed. Make sure that the saw blade cannot be extracted

even though you try to pull it out. (Fig. 5)

NOTE:

• If you do not insert the saw blade deep enough, the

saw blade may be ejected unexpectedly during opera-

tion. This can be extremely dangerous.

If the lever is positioned inside the tool, switch on the tool

just a second to let the blade out as shown in the figure.

Switch off and unplug the tool from mains.

To remove the saw blade, rotate the blade clamp lever in

the direction of the arrow fully. The saw blade is removed

and the blade clamp lever is fixed at the released position

. (Fig. 6)

NOTE:

• Keep hands and fingers away from the lever during the

switching operation. Failure to do so may cause per-

sonal injuries.

• If you remove the saw blade without rotating the blade

clamp lever fully, the lever may not be locked in the

released position . In this case, rotate the blade

clamp lever fully again, then make sure that the blade

clamp lever locked at the released position .

OPERATION (Fig. 7)

CAUTION:

• Always press the shoe firmly against the workpiece

during operation. If the shoe is removed or held away

from the workpiece during operation, strong vibration

and/or twisting will be produced, causing the blade to

snap dangerously.

• Always wear gloves to protect your hands from hot fly-

ing chips when cutting metal.

• Be sure to always wear suitable eye protection which

conforms with current national standards.

• Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause premature blade

wear.

Press the shoe firmly against the workpiece. Do not allow

the tool to bounce. Bring the blade into light contact with

the workpiece. First, make a pilot groove, using a slower

speed. Then use a faster speed to continue cutting.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 8 & 9)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Recipro saw blade

• Plastic carrying case

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 89 dB (A)

Sound power level (L

): 100 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: cutting boards

Vibration emission (a

h,B

): 15.0 m/s

Uncertainty (K): 2.0 m/s

Work mode: cutting wooden beams

Vibration emission (a

h,WB

): 20.0 m/s

Uncertainty (K): 2.5 m/s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita jr3050 t Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita jr3050 t

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info