Bedienungsanleitung Makita JS 1300 (Seite 5 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448565

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ENGLISH

Explanation of general view

1 Switch trigger

2 Lock button

3 Hook

4 Cutting head

5 Screws

6 Loosen

7 Hex wrench

8 Side blade L

9 Center blade

10 Side blade R

11 Sleeve

12 Tighten

13 Side blade surface

14 Side blades

15 Workpiece

16 Lubricate

SPECIFICATIONS

Model JS1300

Max. cutting capacities

Steel up to 400 N/mm

............................. 1.3 mm

Steel up to 600 N/mm

............................. 1.0 mm

Steel up to 800 N/mm

............................. 0.5 mm

Aluminium up to 200 N/mm

.................... 2.5 mm

Strokes per minute ................................... 0 – 2,500

Overall length ............................................. 302 mm

Net weight ...................................................... 1.7 kg

•

Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

•

Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

safety instructions.

ADDITIONAL SAFETY RULES ENB011-2

1. Hold the tool firmly.

2. Secure the workpiece firmly.

3. Keep hands away from moving parts.

4. Edges and chips of the workpiece are sharp.

Wear gloves. It is also recommended that you

put on thickly bottomed shoes to prevent

injury.

5. Do not put the tool on the chips of the work-

piece. Otherwise it can cause damage and

trouble on the tool.

6. Do not leave the tool running. Operate the tool

only when hand-held.

7. Always be sure you have a firm footing. Be

sure no one is below when using the tool in

high locations.

8. Do not touch the blade or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

9. Avoid cutting electrical wires. It can cause

serious accident by electric shock.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Switch action (Fig. 1)

CAUTION:

Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

‘‘OFF’’ position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger.

Release the trigger to stop. For continuous operation,

pull the trigger and then push in the lock button. To

stop the tool from the locked position, pull the trigger

fully, then release it.

Hook (Fig.2&3)

The hook is convenient for temporary hanging the

tool. When using the hook, pull it out in ‘‘A’’ direction

and then push it in ‘‘B’’ direction to secure in place.

When not using the hook, return it back to its initial

position by following the above procedures in reverse.

Replacement of blades

CAUTION:

•

Always be sure that the tool is switched off and

unplugged before replacement of the blades.

•

Never remove the blades with bare hands. Wear

gloves. Otherwise it can cause injury.

Removing cutting head (Fig. 4)

Use the hex wrench to loosen the three screws which

secure the cutting head. Pull the cutting head straight

out to remove it with turning it left and right alternately.

Removing shear blades (Fig. 5)

Remove the three screws which hold the cutting

head. When removing the second screw, be careful

not to fall the sleeve. Then the blades can be removed

easily. When removing the blades, hold the blades

and the sleeve so that they do not fall from the cutting

head.

Installing shear blades (Fig. 6)

Install the sleeve and tighten the three screws after

inserting the center blade, side blade L & R into the

cutting head. In this process, the screw heads should

be protruding 2–3mmfrom the cutting head surface.

If you will tighten the screws excessively, the cutting

head cannot be installed to the tool.

JS1300 (E) (’100. 9. 27)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JS 1300 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita JS 1300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info