Bedienungsanleitung Makita JS 1600 (Seite 4 von 14) (Englisch, Holländisch)

448566

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ENGLISH

Explanation of general view

1 Lower blade

2 Loosen

3 Upper blade

4 Upper blade securing bolt

5 Hex wrench

6 Thin washers

7 Blade holder

8 Tighten

9 No gap allowed

10 Yoke

11 Lower blade positioning screw

12 Lock-off lever in the

FREE position

13 Switch lever (Paddle switch)

14 Lock-off lever in the

LOCK position

15 Lock-off lever

16 Gauge for stainless: 1.2 mm

17 Gauge for mild steel: 1.6 mm

18 Workholder

19 Limit mark

20 Screwdriver

21 Brush holder cap

SPECIFICATIONS

Model JS1600

Max. cutting capacities

Steel up to 400 N/mm

........................... 1.6 mm/16 ga

Steel up to 600 N/mm

........................... 1.2 mm/18 ga

Steel up to 800 N/mm

........................... 0.8 mm/22 ga

Aluminum up to 200 N/mm

................... 2.5 mm/13 ga

Min. cutting radius ................................................ 30 mm

Strokes per minute ................................................. 4,000

Overall length ..................................................... 230 mm

Net weight ............................................................. 1.7 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed Safety

instructions.

ADDITIONAL SAFETY RULES ENB011-2

1. Hold the tool firmly.

2. Secure the workpiece firmly.

3. Keep hands away from moving parts.

4. Edges and chips of the workpiece are sharp.

Wear gloves. It is also recommended that you

put on thickly bottomed shoes to prevent injury.

5. Do not put the tool on the chips of the work-

piece. Otherwise it can cause damage and trou-

ble on the tool.

6. Do not leave the tool running. Operate the tool

only when hand-held.

7. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

8. Do not touch the blade or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

9. Avoid cutting electrical wires. It can cause seri-

ous accident by electric shock.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Blade inspection

Before using the tool, check the blades for wear. Dull,

worn blades will result in poor shearing action, and the

service life of the tool will be shortened.

Rotating or replacing blades

Important:

Always be sure that the tool is switched off and

unplugged before rotating or replacing the blades.

Both the upper and lower blades have four cutting edges

on each side (the front and back). When the cutting edge

becomes dull, rotate both the upper and the lower blades

90° to expose new cutting edges. When all eight edges

are dull on both the upper and lower blades, replace both

blades with new ones. Each time blades are rotated or

replaced, proceed as follows.

Remove the blade securing bolts with the hex wrench

provided and then rotate or replace the blades. (Fig.1)

Some tools have one or more thin washers between the

upper blade and the blade holder. Be sure to use the

same number of thin washers when reassembling. (Note:

No thin washers are used for the lower blade.) (Fig. 2)

To secure the upper blade, tighten the upper blade secur-

ing bolt with the hex wrench. Press up on the upper blade

while tightening it. (Fig. 3)

After securing the upper blade, be sure that there is no

gap left between the upper blade and the bevelled sur-

face of the blade holder. (Fig. 4)

When installing the lower blade onto the yoke, the lower

blade should be pressed against the yoke so as to be

contacting the bevelled portions A and B of the yoke and

the tip C of the lower blade positioning screw while you

tighten the lower blade securing bolt. There must be no

clearance between A, B and C during installation.

(Fig. 5 & 6)

Note:

The lower blade positioning screw is factory-assembled.

Do not tamper with it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JS 1600 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita JS 1600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info