Bedienungsanleitung Makita JS 3200 (Seite 5 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448569

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ENGLISH

Explanation of general view

1 Hex wrench

2 Lower blade

3 Upper blade securing bolt

4 Upper blade

5 Tighten

6 Lower blade securing bolt

7 Blade holder

8 No gap allowed

9 Lower blade positioning bolt

0 Hex nut

q Thickness gauge

w Lock button

e Switch trigger

r Gauge for stainless: 2.5 mm

t Gauge for mild steel: 3.2 mm

y Workholder

u Limit mark

i Screwdriver

o Brush holder cap

SPECIFICATIONS

Model JS3200

Max. cutting capacities

Steel up to 400 N/mm

...................... 3.2 mm/10 ga

Steel up to 600 N/mm

...................... 2.5 mm/13 ga

Steel up to 800 N/mm

...................... 1.5 mm/17 ga

Aluminum up to 200 N/mm

................. 4.0 mm/9 ga

Min. cutting radius ......................................... 50 mm

Strokes per minute .......................................... 1,600

Overall length ............................................... 204 mm

Net weight ....................................................... 3.5 kg

•

Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

•

Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

Safety instructions.

ADDITIONAL SAFETY RULES ENB011-2

1. Hold the tool firmly.

2. Secure the workpiece firmly.

3. Keep hands away from moving parts.

4. Edges and chips of the workpiece are sharp.

Wear gloves. It is also recommended that you

put on thickly bottomed shoes to prevent

injury.

5. Do not put the tool on the chips of the work-

piece. Otherwise it can cause damage and

trouble on the tool.

6. Do not leave the tool running. Operate the tool

only when hand-held.

7. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

8. Do not touch the blade or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

9. Avoid cutting electrical wires. It can cause

serious accident by electric shock.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Blade inspection

Before using the tool, check the blades for wear. Dull,

worn blades will result in poor shearing action, and

the service life of the tool will be shortened.

The service life of the blades varies in terms of the

materials to be cut and the fixed blade clearance.

Roughly speaking, a blade can cut about 500 m of

3.2 mm mild steel with one cutting edge (total 2,000 m

with four cutting edges).

Rotating or replacing blades

Important:

Always be sure that the tool is switched off and

unplugged before rotating or replacing the blades.

Both the upper and lower blades have four cutting

edges. When the cutting edge becomes dull, rotate

both the upper and the lower blades 90° to expose

new cutting edges. When all four edges are dull on

both the upper and lower blades, replace both blades

with new ones. Each time blades are rotated or

replaced, proceed as follows.

Remove the blade securing bolts with the hex wrench

provided and then rotate or replace the blades.

(Fig. 1)

Install the upper blade and tighten the upper blade

securing bolt with the hex wrench. Press up on the

upper blade while tightening it. (Fig. 2)

After securing the upper blade, be sure that there is

no gap left between the upper blade and the bevelled

surface of the blade holder. (Fig. 3)

Then install the lower blade like the upper blade while

adjusting the clearance between the upper blade and

lower blades. When performing this adjustment, the

upper blade should be in the lowered position. First,

semi- tighten the lower blade securing bolt, then insert

the thickness gauge for the desired clearance. The

cutting thickness is indicated on the thickness gauge

so the combinations shown in the table below should

be used. Work the lower blade positioning bolt on the

yoke until the clearance is such that the thickness

gauge moves only with some difficulty. Then firmly

tighten the lower blade securing bolt. Finally, tighten

the hex nut to secure the lower blade positioning

bolt. (Fig.4&5)

JS3200 (E) (’101. 1. 12)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JS 3200 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita JS 3200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info