Bedienungsanleitung Makita JV0600K (Seite 8 von 13) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

711079

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

2) Circular cuts (Fig. 18 & 19)

When cutting circles or arcs of 170 mm or less in

radius, install the rip fence as follows.

Insert the rip fence into the rectangular hole on the

side of the base with the fence guide facing up.

Insert the circular guide pin through either of the two

holes on the fence guide. Screw the threaded knob

onto the pin to secure the pin.

Now slide the rip fence to the desired cutting radius,

and tighten the bolt to secure it in place. Then move

the tool base all the way forward.

NOTE:

• Always use blades No. B-17, B-18, B-26 or B-27 when

cutting circles or arcs.

Anti-splintering device (Optional accessory)

(Fig. 20)

For splinter-free cuts, the anti-splintering device can be

used. To install the anti-splintering device, move the tool

base all the way forward and fit it from the back of tool

base. When you use the cover plate, install the anti-splin-

tering device onto the cover plate.

CAUTION:

• The anti-splintering device cannot be used when mak-

ing bevel cuts.

Cover plate (Optional accessory) (Fig. 21)

Use the cover plate when cutting decorative veneers,

plastics, etc. It protects sensitive or delicate surfaces

from damage. Fit it on the back of the tool base.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Jig saw blades

• Hex wrench 3

• Rip fence (guide rule) set

• Anti-splintering device

• Hose (For vacuum cleaner)

• Cover plate

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 85 dB (A)

Sound power level (L

): 96 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: cutting boards

Vibration emission (

h, B

): 10.5 m/s

Uncertainty (K): 1.5 m/s

Work mode: cutting sheet metal

Vibration emission (

h, M

): 5.5 m/s

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been mea-

sured in accordance with the standard test method and

may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the oper-

ator that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger time).

ENH101-15

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible manufac-

turer declare that the following Makita machine(s):

Designation of Machine: Jig Saw

Model No./ Type: JV0600

are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following

standards or standardised documents:

EN60745

The technical documentation is kept by our authorized

representative in Europe who is:

Makita International Europe Ltd.

Michigan Drive, Tongwell,

Milton Keynes, Bucks MK15 8JD, England

18.11.2010

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, 446-8502, JAPAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JV0600K Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info